picco .26
#1
picco .26
i have a old ofna picco .26 big block with the purple head. I don't think they make it anymore. It's a pretty old one, and it threw a rod. The crank, case, carb and everything else is ok. I want to get a new P/S and rod.
So basically i am rebuilding it. I found some parts online, but some say .26 force and has a blue head. I found one that is .26 picco. Will theese work in my motor?
It was a motor given to me from a friend and is pretty old. anywhere from 5 to 10 years. Same company, same style.
And it would only cost me about 80$ for a rebuild. And let me tell you, this motor is one bad mofo. It's too much for my buggy so i plan on putting it in my truggy that i will be building.
Opinions please?
So basically i am rebuilding it. I found some parts online, but some say .26 force and has a blue head. I found one that is .26 picco. Will theese work in my motor?
It was a motor given to me from a friend and is pretty old. anywhere from 5 to 10 years. Same company, same style.
And it would only cost me about 80$ for a rebuild. And let me tell you, this motor is one bad mofo. It's too much for my buggy so i plan on putting it in my truggy that i will be building.
Opinions please?
#3
i have a old ofna picco .26 big block with the purple head. I don't think they make it anymore. It's a pretty old one, and it threw a rod. The crank, case, carb and everything else is ok. I want to get a new P/S and rod.
So basically i am rebuilding it. I found some parts online, but some say .26 force and has a blue head. I found one that is .26 picco. Will theese work in my motor?
It was a motor given to me from a friend and is pretty old. anywhere from 5 to 10 years. Same company, same style.
And it would only cost me about 80$ for a rebuild. And let me tell you, this motor is one bad mofo. It's too much for my buggy so i plan on putting it in my truggy that i will be building.
Opinions please?
So basically i am rebuilding it. I found some parts online, but some say .26 force and has a blue head. I found one that is .26 picco. Will theese work in my motor?
It was a motor given to me from a friend and is pretty old. anywhere from 5 to 10 years. Same company, same style.
And it would only cost me about 80$ for a rebuild. And let me tell you, this motor is one bad mofo. It's too much for my buggy so i plan on putting it in my truggy that i will be building.
Opinions please?
If I recall correctly OFNA makes three different .26 motor = .26 max, .26 red dot and .26 force.
The motor your describing is a .26 force different from the max and red dot the case is different making the rod different (Not Sure) but Parts are available. Ofna, Nitro House, ebay
#4
this is excactly the engine i am talking about
http://d214892.u44.digipark.com/item...OFNAPICCO26NPS
http://d214892.u44.digipark.com/item...OFNAPICCO26NPS
#5
this is the one i want to rebuild.
#6
bump
#8
they have red dot, max, and force. The engine i have shown here is over five years old. I want to make sure i get the right parts.
#9
this is excactly the engine i am talking about
http://d214892.u44.digipark.com/item...OFNAPICCO26NPS
http://d214892.u44.digipark.com/item...OFNAPICCO26NPS
call them
#10
$ for $ i can tell you right now your better off scraping it and getting something new....Picco's are cheap enough to not justify rebuilding...your gonna get quotes 150$+ for a new P+S i can almost guarantee that....Junk it Dreaux and save the headache for another day.
I STAND corrected....Dreaux your right its only 70$ for the P+S.....One of Very few Ofna/jammin motor's that Might be worth it.
I STAND corrected....Dreaux your right its only 70$ for the P+S.....One of Very few Ofna/jammin motor's that Might be worth it.
Last edited by Integra; 12-30-2009 at 01:57 PM.
#12
curious have you ever used one of those clamps ? If not why would you think they would be an alternative to a proper pinching machine that's in the range of 600$+ ?
Some machines are 100,000.00$+ and are used for pinching but you think a 12$ tool will cut it for your reasonable expensive P+S ?
#14
Tech Champion
iTrader: (82)
curious have you ever used one of those clamps ? If not why would you think they would be an alternative to a proper pinching machine that's in the range of 600$+ ?
Some machines are 100,000.00$+ and are used for pinching but you think a 12$ tool will cut it for your reasonable expensive P+S ?
Some machines are 100,000.00$+ and are used for pinching but you think a 12$ tool will cut it for your reasonable expensive P+S ?
just some of the things he says i was just poking fun at him, if he cant take it then i am sorry LOL!
#15
integra, it was a extenuation of my eternal gratitude of such a sagacious, omniscient man. Matter of fact, DREAUX is not merely a man. He transcends greatness!!!!
just some of the things he says are absolute and inrefutable. I don't mean to be erroneous, i just can't help it. My parents should have never been allowed to breed. It's all thier fault
just some of the things he says are absolute and inrefutable. I don't mean to be erroneous, i just can't help it. My parents should have never been allowed to breed. It's all thier fault
Why thank you kind sir! Such a gentlemen you are