1LikesKyosho VoneR Thread
04-09-2003, 05:33 AM
#6571
Originally posted by Sydewynder
Texas!! Oh no you're moving closer!!
You know what they say, When the cat's away the mice will play.
Live it up, for now.
Oh one thing about the Barracuda, hope you like about 4 degree rear toe-in.
Texas!! Oh no you're moving closer!!
You know what they say, When the cat's away the mice will play.
Live it up, for now.Oh one thing about the Barracuda, hope you like about 4 degree rear toe-in.
04-09-2003, 11:20 AM
#6572
Originally posted by patelladragger
I didn't buy the cuda somebody beat me to it. But you're saying a 300+ dollar car doesn't have adjustable rear toe? hmmm..............
I didn't buy the cuda somebody beat me to it. But you're saying a 300+ dollar car doesn't have adjustable rear toe? hmmm..............
Guess the toe wasn't from the arm angle. Hope Speedtech will get optional parts.
04-10-2003, 09:07 PM
#6574
Tech Master
Originally posted by Sushi Boy
Can someone give me a decent starting setup for a V-One R for runnning on a smooth prepared asphalt and with foam tires. Thanks.
Can someone give me a decent starting setup for a V-One R for runnning on a smooth prepared asphalt and with foam tires. Thanks.
Take the time and start from the beginning
04-11-2003, 10:38 AM
#6576
Originally posted by Sushi Boy
220 pages, from the begining.......oh ok. I have nothing else better to do anyways.
220 pages, from the begining.......oh ok. I have nothing else better to do anyways.
04-11-2003, 04:41 PM
#6578
Originally posted by Im2lazy
That is quite plainly insane...
That is quite plainly insane...
04-11-2003, 09:03 PM
#6580
How did u guys configure your servo wires and everything my wires are a bunch and dont know where to stuff em at. 
04-11-2003, 09:52 PM
#6581
Originally posted by NitroNut
How did u guys configure your servo wires and everything my wires are a bunch and dont know where to stuff em at.
How did u guys configure your servo wires and everything my wires are a bunch and dont know where to stuff em at.
04-11-2003, 09:53 PM
#6582
Tech Master
Originally posted by Sushi Boy
Well, Im on page 60 right now, havent; really found any setupos that will seem to work at my track but lots and lots of good info.
Well, Im on page 60 right now, havent; really found any setupos that will seem to work at my track but lots and lots of good info.
trust me write some of those set ups down on some paper and try them, you might surprise yourself
04-11-2003, 09:54 PM
#6583
Tech Master
Originally posted by Taylor-Racing
Please, please, please . . . can I answer this one
Please, please, please . . . can I answer this one
04-11-2003, 10:00 PM
#6584
Originally posted by NitroNut
How did u guys configure your servo wires and everything my wires are a bunch and dont know where to stuff em at.
How did u guys configure your servo wires and everything my wires are a bunch and dont know where to stuff em at.
Run the steering servo wire under the top deck - to do this, drill a hole beside the servo and use a rubber grommet. Gather all wires and fold on top of the receiver. Use a rubber band to hold it all in place. Stretch a balloon over the whole lot and use a cable tie to fix to the holder. Screw the holder into place.
Easy.
04-11-2003, 10:05 PM
#6585
Tech Master
Originally posted by Taylor-Racing
Oh, all right then, I'll be nice . . .
Run the steering servo wire under the top deck - to do this, drill a hole beside the servo and use a rubber grommet. Gather all wires and fold on top of the receiver. Use a rubber band to hold it all in place. Stretch a balloon over the whole lot and use a cable tie to fix to the holder. Screw the holder into place.
Easy.
Oh, all right then, I'll be nice . . .
Run the steering servo wire under the top deck - to do this, drill a hole beside the servo and use a rubber grommet. Gather all wires and fold on top of the receiver. Use a rubber band to hold it all in place. Stretch a balloon over the whole lot and use a cable tie to fix to the holder. Screw the holder into place.
Easy.