Mugen MRX-4
#916
And if you put a small screw in this center part.....
#917
Tech Master
iTrader: (6)
Originally Posted by US_MATRIX
Option rear body mount?
Does Mugen or thrid body make an option rear body mount to keep the rear body mount NOT popping out from the center? If it is available, what is the part number? The problem to my car is once in every few runs the rear mount will pop out from the center.
Thanks.
Does Mugen or thrid body make an option rear body mount to keep the rear body mount NOT popping out from the center? If it is available, what is the part number? The problem to my car is once in every few runs the rear mount will pop out from the center.
Thanks.
http://www.h3.dion.ne.jp/~khc/mrx4centerpost.html
#918
Tech Regular
Hi there!
Together with my Protoform Lola T530 bdy came this plastic part that looks like a shovel or a wing. Does anybody know whats that for?
EDIT: Thanks, itīs clear now
Together with my Protoform Lola T530 bdy came this plastic part that looks like a shovel or a wing. Does anybody know whats that for?
EDIT: Thanks, itīs clear now
Last edited by fulcrum2; 01-05-2006 at 10:28 AM.
#919
Those are the body supports...need to be cut apart and placed (screwed or riveted) inside the body to stiffen the sides.
#920
Tech Regular
Ah! Thanks Ralph!
I think most drivers are not using them, because Iīve asked some guys at my local track and they didīnt had a clue...
I think most drivers are not using them, because Iīve asked some guys at my local track and they didīnt had a clue...
#922
Tech Regular
Thanks guys for claification!
Btw, could anybody advice on the head shims (scroll a few post up)?
Btw, could anybody advice on the head shims (scroll a few post up)?
#923
Originally Posted by fulcrum2
Thanks guys for claification!
Btw, could anybody advice on the head shims (scroll a few post up)?
Btw, could anybody advice on the head shims (scroll a few post up)?
I would leave the clearance as it is set now.
If your engine needs more bottom, you can remove 0.1-0.2 mm.......
I have a NovaMAX MF (ok, it is Massimo F. hand tuned), with approx. the same head clearance, it runs like hell, enough bottom and a very high top speed.......
#924
Tech Regular
OK, will do so. Thank you very much!
#925
Tech Elite
iTrader: (23)
Any guys getting their car's ready for racing? I'm going to try and drive my 8th maybe tomorrow. I still remembering from last time how come I can't get that thing to stop spinning out even when going slow. Figured maybe the tires might be off, or the adjuster nut may be too tight. However the adjuster nut isn't showing a thread and yet the manual says .6mm to 1mm. I'll run some test tomorrow though and maybe even run the tires I was saving for track only. There's a possible chance I may just run 8th onroad this year only.
#926
MRX-4 miniture style
#928
Tech Master
iTrader: (92)
Originally Posted by HarKonnenD
Any guys getting their car's ready for racing? I'm going to try and drive my 8th maybe tomorrow. I still remembering from last time how come I can't get that thing to stop spinning out even when going slow. Figured maybe the tires might be off, or the adjuster nut may be too tight. However the adjuster nut isn't showing a thread and yet the manual says .6mm to 1mm. I'll run some test tomorrow though and maybe even run the tires I was saving for track only. There's a possible chance I may just run 8th onroad this year only.
#929
Tech Elite
iTrader: (23)
I'm currently debating on going to bridgeport or brooklyn as of right now. It's 10:07am. Today and tomorrow will be awesome though I'm on a time limit. Today I have to get my mom at 5:30pm and tomorrow I have to be at work by 5pm. Wednesday of all my favorite days will rain That's the day in the week that I don't have work or school.
#930
ha sohlman good luck at the winter nats.
i am fully insured now
see you at the next local race
i am fully insured now
see you at the next local race