BANZAI Motors
01-26-2007, 06:47 PM
#2641
Hi Brandon, glad you found us here! 
If you need any help, just let us know!
They should be little "missles" !!!
I expect to see your name in "lights" in the
SoCal results for this week-end!!
Judi
If you need any help, just let us know!
They should be little "missles" !!!
I expect to see your name in "lights" in the
SoCal results for this week-end!!
Judi
01-26-2007, 06:57 PM
#2642
I'll be there sunday to see those motors go 
Erik: you at socal or at home? I see you on. Home sick?
Erik: you at socal or at home? I see you on. Home sick?
01-26-2007, 07:25 PM
#2643
Tech Master
WHATS UP ALL. WHERE IS EVERBOBY.NOBODYS ON THIS THING TONIGHT 
01-26-2007, 07:50 PM
#2645
I feel like a big dope 
I bought a Carbide bit for $10 then later realized I could get them from McMaster carr as well. They sale tem for $3.59 retail but I got them for $1.80 each. The $10 one I got is from Mcmaster carr as I just got 3 today from them and they are marked with the same name. Man did I get ripped off
I bought a Carbide bit for $10 then later realized I could get them from McMaster carr as well. They sale tem for $3.59 retail but I got them for $1.80 each. The $10 one I got is from Mcmaster carr as I just got 3 today from them and they are marked with the same name. Man did I get ripped off
01-26-2007, 08:02 PM
#2647
Tech Adept
Me and my buddy Kenny will be there - i took novice last week, he took Int...although, new batteries and motors came in this week...watch out for us new guys ...hope to meet some of you i've met on here in person!
Casper - just went to Ultimate, they didn't have my 17 pinion, hopefully SoCal will
...hope to meet some of you i've met on here in person!Casper - just went to Ultimate, they didn't have my 17 pinion, hopefully SoCal will
01-26-2007, 08:16 PM
#2649
Originally Posted by brandonizr
Me and my buddy Kenny will be there - i took novice last week, he took Int...although, new batteries and motors came in this week...watch out for us new guys ...hope to meet some of you i've met on here in person!
Casper - just went to Ultimate, they didn't have my 17 pinion, hopefully SoCal will
...hope to meet some of you i've met on here in person!Casper - just went to Ultimate, they didn't have my 17 pinion, hopefully SoCal will
Socal should most definately have a 17T pinion. If not, I'm sure someone will let you borrow one
I'll call you tomorrow
01-26-2007, 08:49 PM
#2651
Anyone have a couple of old armatures laying around? I want to practice a little more turning the comms before I start cutting good motors.
Scot - What was the name of the place that could lap my bit?
Thanks!
Scot - What was the name of the place that could lap my bit?
Thanks!
Last edited by JamesnMeyer; 01-26-2007 at 11:30 PM.
01-27-2007, 05:48 AM
#2652
Tech Master
GOOD DAY ALL .HEY SCOTT JOE L WE FIRED HIM 
01-27-2007, 06:26 AM
#2653
I have 3 Banzai 27 trurn stock motors. How long do I need to break them in after I cut the com. and Serade the brushes? Also what is the min. com. Diameter? I'm looking for max torque for our tight track only has 1 50 ft straight away.
Thanks
Jake
Thanks
Jake
01-27-2007, 08:32 AM
#2654
James: The name is Westec Diamond Tool. They're in Yorba Linda.
714-993-2510
Bob: Morning Bud. HEY SCOTT JOE L WE FIRED HIM Good!!!!!!
Hawktoy85: You really only need to break in those motors just a few seconds. Then put them in your car or truck and run them. Minimum comm dia. is .270. Good luck. 
714-993-2510
Bob: Morning Bud. HEY SCOTT JOE L WE FIRED HIM Good!!!!!!
Hawktoy85: You really only need to break in those motors just a few seconds. Then put them in your car or truck and run them.
Minimum comm dia. is .270. Good luck.