Serpent 710
#4711
Originally posted by Rookie Solara
Initial D (or others who knows).........I have a question for you, I remembered back some 20-30 plus pages ago, you posted a picture on the Centax 3 flyweight modification (cuted the end of the weight and place it in between the shaft)..........I can't seems to find it, would you please direct me to the # of that page....
Thanks..........
Initial D (or others who knows).........I have a question for you, I remembered back some 20-30 plus pages ago, you posted a picture on the Centax 3 flyweight modification (cuted the end of the weight and place it in between the shaft)..........I can't seems to find it, would you please direct me to the # of that page....
Thanks..........
#4712
Originally posted by Sow&Steady
Hope you kick ass!
Hope you kick ass!
I think that race you mentioned was the first race the track held. It clashed with another race which I participated. I think it was at the Shah Alam race. The last race (you were probably not there) belonged to Wong. Racers from Sabah also came if I'm not mistaken.
#4713
Originally posted by Sow&Steady
Well, I haven't broken one yet but mine was cracked a little bit after going turtle. Since a lot of guys were breaking them I decided to buy another one and double up. I just used slow setting superglue and pasted the two together. Now it looks rock solid!
Well, I haven't broken one yet but mine was cracked a little bit after going turtle. Since a lot of guys were breaking them I decided to buy another one and double up. I just used slow setting superglue and pasted the two together. Now it looks rock solid!
#4714
Originally posted by crashed_1
I just stripped a spur today after 2 tanks...16/61 and 21/57. But managed to play the whole day with a 16/60 and 21/56.
I just stripped a spur today after 2 tanks...16/61 and 21/57. But managed to play the whole day with a 16/60 and 21/56.
I'm on 17/61 and 22/56. Been with that gearing since the early days I started running the 710.
#4715
Originally posted by Rookie Solara
I have 1 more question, it is about my 835 (upgraded from 02 spec).....which 2-speed and centax can I use beside the Centax 1...?
I have 1 more question, it is about my 835 (upgraded from 02 spec).....which 2-speed and centax can I use beside the Centax 1...?
The only difference between the Centax 1 and Centax 2 is the flyweights (no retainer spring), the harder Centax spring (1.8 mm versus 1.7 mm) and the bearings (bigger normal bearing and thrust bearings). Centax 2 (which comes with the 705 and the 835 kit) uses the same pinions. Therefore the Centax 2 clutch will mesh with the older Centax 1 spurs found on the Impact with some minor mod.
Originally posted by Rookie Solara
but will 835 2-speed (same as the 705) work with the Centax 3?
but will 835 2-speed (same as the 705) work with the Centax 3?
Originally posted by Rookie Solara
Will the 2-speed gear box of 705 work with the centax 3 with the centax 2 pinion gears....? Thanks
Will the 2-speed gear box of 705 work with the centax 3 with the centax 2 pinion gears....? Thanks
#4716
JESUS "D". Your a wealth of knowledge! Your like an Encyclopedia I know who to come to when I've got questions about putting my 710 together!
#4717
Originally posted by InitialD
Perhaps get our arses kicked instead !
I think that race you mentioned was the first race the track held. It clashed with another race which I participated. I think it was at the Shah Alam race. The last race (you were probably not there) belonged to Wong. Racers from Sabah also came if I'm not mistaken.
Perhaps get our arses kicked instead !
I think that race you mentioned was the first race the track held. It clashed with another race which I participated. I think it was at the Shah Alam race. The last race (you were probably not there) belonged to Wong. Racers from Sabah also came if I'm not mistaken.
#4718
Originally posted by InitialD
Yeah, we know who swipped all the rear shock towers in town !
Yeah, we know who swipped all the rear shock towers in town !
#4719
Originally posted by InitialD
I'm on 17/61 and 22/56. Been with that gearing since the early days I started running the 710.
I'm on 17/61 and 22/56. Been with that gearing since the early days I started running the 710.
Are you racing at Andalas today? Hmmm
#4720
On Throttle Understeer
Hope I can get some feed back by tomorrow.
My 710 has been running perfect all weekend long. The mods clutch really adds some potent kick out of corners and I feel like there's more top end speed too.
The only thing that I need some input in setting up the 710 is that the car has a tad tendency to run sidewide while accelerating out of corner on power. I've tried sliding in the rear swaybar ball end 4mm, full caster and tightening rear diff. The car still can't keep its line tight accelerating out of corners (high speed corners).
My 710 has been running perfect all weekend long. The mods clutch really adds some potent kick out of corners and I feel like there's more top end speed too.
The only thing that I need some input in setting up the 710 is that the car has a tad tendency to run sidewide while accelerating out of corner on power. I've tried sliding in the rear swaybar ball end 4mm, full caster and tightening rear diff. The car still can't keep its line tight accelerating out of corners (high speed corners).
#4721
Today I was running new tires which are 37 shores front and rear. Man I was doing cart wheels all day long I guess the tires doesnt suit the track since the track is high bite. Had to get new 40 shores in the rear and use my sotck tires up front which worked out pretty good. Crack my front bumper and lost my front pulley belt as well as the pulley up front. I think it has to do with the car flipping too much
#4722
I got a question. Lets say all your suspenion is tuned right and the springs are all adjusted so that it has even preload all around then why does the car still tweaked when doing the lifting method? I made sure the sway bars were disconnect and stuff but the car still has a bit of tweak when I lift it. Does it have to do with anything with the car being not perfectly balanced out of the box as in the rear left might be heavier than the rest? So in my situation do you think it is because the car is heavier in one corner and no matter what you still need to adjust the individual springs preload because the car does not weight the same in each wheel? Has anyone put the 710 on all 4 scales to see which side is heavier? I doubled check to make sure all the springs were adjusted with exact preload when turning the spring collar. Sorry if it sounds confusing. The only thing I can think of is maybe the shocks compression or rebound could be off? Maybe I need to rebuild the shocks There are too many things that could be wrong so maybe someone can shine some light
#4723
chassis may be tweaked.
#4724
Originally posted by Aggdaddy
chassis may be tweaked.
chassis may be tweaked.
#4725
Originally posted by cyba888
Do you mean as in bent or crooked?
Do you mean as in bent or crooked?
Cheers, Mark.