GT class--buggy-based on road!
05-18-2011, 10:15 AM
#6136
I have a Spektrum H6050(identical to Savox 1258) on gas/brakes, and the Tower equivalent of a Hitec 5955 on steering. The Tower servo is somehow noticeably slower than the Hitec 5955 I have in my SC8.
I'm gonna outfit a new 1/8 DM-1 Spec soon, and I think I'm gonna go with Savox 1258's for both servos. Laser-quick...
I'm gonna outfit a new 1/8 DM-1 Spec soon, and I think I'm gonna go with Savox 1258's for both servos. Laser-quick...
05-18-2011, 10:50 AM
#6137
Thankz fellas for the feed back i'm going to start looking into it cause jr servos cost to much.
05-18-2011, 11:47 AM
#6139
05-18-2011, 11:56 AM
#6140
KO servo GOOD
That KO servo you lend me was great 1speedy. Thanks you saved the race day for me I replaced my JR z9100hvs with another one of the same. But know KO is up in rank with me also. That was my first experience with a KO.
05-18-2011, 01:05 PM
#6142
05-18-2011, 01:53 PM
#6143
New pic of Jai's slick ride. 
05-18-2011, 01:54 PM
#6144
05-18-2011, 03:11 PM
#6146
Guy's, I am looking into this class.
Is the two speed absolutely necessary?
I got to do this low buck for a bit.
Going to convert a buggy and run some old
off road motors I have.
If I need the two speed..Who makes the cheapest unit?
Got stuff sitting here going to waste,might
as well try and make it work.
Is the two speed absolutely necessary?
I got to do this low buck for a bit.
Going to convert a buggy and run some old
off road motors I have.
If I need the two speed..Who makes the cheapest unit?
Got stuff sitting here going to waste,might
as well try and make it work.
http://www.nitrohouse.com/advanced_s...12a860&x=0&y=0
I've used others but this is the one that's been less hassle for me to get parts, plus it's also used on the Ofna DM1 spec.
05-18-2011, 03:28 PM
#6147
This is the one I use
http://www.nitrohouse.com/advanced_s...12a860&x=0&y=0
I've used others but this is the one that's been less hassle for me to get parts, plus it's also used on the Ofna DM1 spec.
http://www.nitrohouse.com/advanced_s...12a860&x=0&y=0
I've used others but this is the one that's been less hassle for me to get parts, plus it's also used on the Ofna DM1 spec.
05-18-2011, 05:55 PM
#6148
Tech Master
iTrader: (4)
Join Date: Mar 2009
Location: Tween a Rock & a Hard Place in Pa.
Posts: 1,279
Trader Rating: 4 (100%+)
OMG now I have the nitro itch back
and a couple o buggys and truggys ta convert ta a "frank"
and K mans gt is NUTZ ya should see it on the T&L track--OMG.
and a couple o buggys and truggys ta convert ta a "
frank"and K mans gt is NUTZ ya should see it on the T&L track--OMG.
05-18-2011, 06:08 PM
#6149
Tech Master
iTrader: (4)
Join Date: Mar 2009
Location: Tween a Rock & a Hard Place in Pa.
Posts: 1,279
Trader Rating: 4 (100%+)
can u run a drift system in these
05-18-2011, 06:27 PM
#6150