New Pursuit SPT1 1/10 Scale 4WD
01-21-2009, 11:32 PM
#16
Tech Apprentice
looks great!
how much will it be?
how much will it be?
01-22-2009, 12:35 AM
#17
Thanks all for all your comments it's very important when anyone tell's you something, this is the way to improve your products, I still learning this business and try to put on the market the best products possible to be competitive and best quality to, with lower price possible I know a lot of people do not believe when you tell them this product is good when the price is lower then the competition, but I try to do business the best way is possible end honest to.
Thanks all I will see you @ Race Track and have a very nice new Year
Thanks all I will see you @ Race Track and have a very nice new Year
Just 2 suggestions for SPT1's graphite upper deck :
( you don't have to follow if you think is not necessary )
1. The graphite L section near steering servo is too narrow for my taste. Possible breakage from medium impacts.
2. Isn't it better to use PT1's radio box + four elongated holes design (to put a throttle servo ) for SPT1 ?
I think PT1's radio plate should be copy for SPT1.
01-22-2009, 06:00 AM
#18
Hi! Terry, how are you? just wanna know when are you going to Fort Myers..
Take care now......FEB
Take care now......FEB
01-22-2009, 11:18 AM
#19
01-22-2009, 11:19 AM
#20
Hi Terry, I look at the webpage and look at the car photo closely. It's nice car.
Just 2 suggestions for SPT1's graphite upper deck :
( you don't have to follow if you think is not necessary )
1. The graphite L section near steering servo is too narrow for my taste. Possible breakage from medium impacts.
2. Isn't it better to use PT1's radio box + four elongated holes design (to put a throttle servo ) for SPT1 ?
I think PT1's radio plate should be copy for SPT1.
Just 2 suggestions for SPT1's graphite upper deck :
( you don't have to follow if you think is not necessary )
1. The graphite L section near steering servo is too narrow for my taste. Possible breakage from medium impacts.
2. Isn't it better to use PT1's radio box + four elongated holes design (to put a throttle servo ) for SPT1 ?
I think PT1's radio plate should be copy for SPT1.
01-22-2009, 11:22 AM
#21
01-22-2009, 11:33 AM
#22
01-22-2009, 11:50 AM
#23
Tech Rookie
01-22-2009, 01:00 PM
#25
This kit looks like a brother to the Kyosho RRR. I'd have to take measurements but the chassis alone looks almost identical to the RRR. The layout is certainly the same. Uppper deck is a bit different and there does appear to be a couple spots where I could see the possibilty for breakage from a hard impact. I do like the adjustability on the rear hub carriers. Can't see the full tank but it looks a bit narrow and tall. Might have a higher CG. Nice looking kit.
Regards,
Speyederjedi
Regards,
Speyederjedi
01-27-2009, 03:56 PM
#26
We try all best to make it the best race car of the market!!!
02-13-2009, 08:12 AM
#27
what
Terry the car looks good brotha...keep doin what your doin..
I sent you and e-mail about two weeks ago.
If you didn't get it hit me at [email protected]
Its time to do some 1/10 testing at 301
Good Luck
Denmark
I sent you and e-mail about two weeks ago.
If you didn't get it hit me at [email protected]
Its time to do some 1/10 testing at 301
Good Luck
Denmark
02-13-2009, 12:49 PM
#28
I drive the 1/8 Pursuit car and it handles just like any car out there. It looks like a combo of the Kyosho and Serpent. Like any car driver skill and set up is always a must. Keep up the good work Terry!
Dan in VA.
Dan in VA.
06-05-2011, 04:39 AM
#29
Tech Initiate
Sorry to dig up an old thread, after three years is this company no more? The website domain has expired!
Thanks
Thanks
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
