113LikesFutaba 7PX
05-07-2019, 09:25 AM
#526
From my readings you can link the receiver to run in SR mode for the fastest response you just can't turn on SR mode for the channels (Servos) it needs to stay off.
05-07-2019, 10:30 AM
#527
Tech Fanatic
iTrader: (36)
I been using my new cb700 servos and they do work on sr more type 3 which is suppose to be faster. My s9373 servo only works in sr mode type1.
and yes you can bind the receiver in sr mode and use a non sr servo as long as sr mode is turned off on the channel of the servo.
and yes you can bind the receiver in sr mode and use a non sr servo as long as sr mode is turned off on the channel of the servo.
05-08-2019, 10:55 AM
#528
My 7PX will be here tomorrow I hope it's worth the $$$, It looks like a lot of the top drivers trust Sanwa's M17. Or they get them for free or a check...lol
05-09-2019, 05:59 AM
#530
Those top drivers usually get their Sanwa radios free. Futaba sponsor more on the aircraft side than the surface side it seems.
05-10-2019, 08:23 PM
#532
Wow...got my 7PX and man is it nice, however I think it is full of options and settings you will probably never need. I think it is over priced and you get more bang for your buck with the M17.
05-11-2019, 04:36 AM
#533
Is it possible to transfer all the model from my 4px to the 7px? Also if I order the 7px from RCMart and have it shipped to the US will Futaba still warranty it? Is it the same version that US dealers sell?
Last edited by Raydee; 05-11-2019 at 05:32 AM.
05-19-2019, 01:33 AM
#535
Your local mobile phone shop. Get an oversized sheet and cut it to the right dimension.
05-22-2019, 08:10 AM
#536
Conditions
Hello ppl
had my 7px about say 2-3months now and there is a feature I don't understand how to get it to work "conditions" .
So far all I have been able to do is map the PS5 button to conditions #1<>2
but I can't get the settings in #2 to be different from condition #1.
example Condition #1 dual rate 100, end points 90/90, lights off
. Condition #2 dual rate 90, end points 30/100, lights on
What to use the feature to slow the car down for a kid to drive. Ya know that random kid that ask can I have a go.
I have read the manul back to front and I just don't get it, there's no mention on how to change the settings for condition #2/3/4 .
Thanks
Any help would be appreciated thanks.
had my 7px about say 2-3months now and there is a feature I don't understand how to get it to work "conditions" .
So far all I have been able to do is map the PS5 button to conditions #1<>2
but I can't get the settings in #2 to be different from condition #1.
example Condition #1 dual rate 100, end points 90/90, lights off
. Condition #2 dual rate 90, end points 30/100, lights on
What to use the feature to slow the car down for a kid to drive. Ya know that random kid that ask can I have a go.
I have read the manul back to front and I just don't get it, there's no mention on how to change the settings for condition #2/3/4 .
Thanks
Any help would be appreciated thanks.
06-20-2019, 01:13 AM
#539
My measurements on the SR mode is a 760uS center pulse and an 800Hz framerate.
This one does comply:
https://www.xpert-rc-us.com/product/...luminum-servo/
This is the only one I have found and is not a SBUS servo so it needs to be connected to the normal channel.
This one does comply:
https://www.xpert-rc-us.com/product/...luminum-servo/
This is the only one I have found and is not a SBUS servo so it needs to be connected to the normal channel.
