65LikesTC3 Forum
03-08-2002, 01:58 PM
#1336
Tech Master
Associated make the best ride height gauge. It comes in 1/2 mm increments and and added bonus....ITS BLUE!!! 
Part # 1450
Part # 1450
03-08-2002, 02:12 PM
#1337
I use the Hudy ride height guage with marks at each 0.5 mm and without steps
03-08-2002, 03:33 PM
#1338
Modena......i had that part #, but didnt know if it had the 1/2 mm. increments....thanks....GO BLUE
03-08-2002, 04:17 PM
#1339
Tech Adept
Does anyone know of any hex adaptors slightly wider than the stock ones? I noticed since the TC3 isnt the whole 190mm that I could add some width and still be within the rules.
03-08-2002, 04:44 PM
#1340
Originally posted by patcollins
Does anyone know of any hex adaptors slightly wider than the stock ones? I noticed since the TC3 isnt the whole 190mm that I could add some width and still be within the rules.
Does anyone know of any hex adaptors slightly wider than the stock ones? I noticed since the TC3 isnt the whole 190mm that I could add some width and still be within the rules.
03-08-2002, 05:42 PM
#1341
Tech Regular
Pat,
Check out Integy's website.....and/or....use Yokomo blue aluminum clampon drive hex's.
Check out Integy's website.....and/or....use Yokomo blue aluminum clampon drive hex's.
03-08-2002, 05:56 PM
#1342
Originally posted by Modena AL
Associated make the best ride height gauge. It comes in 1/2 mm increments and and added bonus....ITS BLUE!!!
Part # 1450
Associated make the best ride height gauge. It comes in 1/2 mm increments and and added bonus....ITS BLUE!!!
Part # 1450
haha...
BTW, I already ordered 2 sets of brp polished hinge pins because ti ones are so much expensive.
If you posted before, I could've ordered only one set and sleep well. Man.
I'll just sell them to somebody telling they are ti hinge pins.
Just kidding.
03-08-2002, 06:02 PM
#1343
Originally posted by Airwide
rcruv - I use drill blanks as hinge pins. They are much straighter than the std pins and won't bend. However, they can shear off in a hard crash.
rcruv - I use drill blanks as hinge pins. They are much straighter than the std pins and won't bend. However, they can shear off in a hard crash.
Thanks for the tip.
Hope those work better and cost much less.
03-08-2002, 06:44 PM
#1344
Tech Adept
acloco, happen to know which of the hubs on integy's site most closely matches the stock hubs?
03-08-2002, 07:34 PM
#1345
Tech Regular
Pat,
That .....unfortunately.....I do not know. Sorry.
That .....unfortunately.....I do not know. Sorry.
03-08-2002, 09:25 PM
#1346
Pat, the Integy hubs are metric....
03-08-2002, 09:33 PM
#1347
Tech Adept
they will still work, I guess hub isnt the right way to describe them. Im talking about the hex drives.
03-08-2002, 11:20 PM
#1348
Tech Regular
Pat....yep...that is what you can find on the site.....hex's.
03-09-2002, 09:34 AM
#1349
Anybody making aluminum front body post or have been using them?
Plastic body post are really weak and threads strip all the time.
I wonder if aluminum body post of XXXS would fit.
Plastic body post are really weak and threads strip all the time.
I wonder if aluminum body post of XXXS would fit.
03-09-2002, 10:18 AM
#1350
what is the alum gets bent....that woundnt look too good :P