EAMotorsports discussion thread
#7306
Tech Adept
I am running ORCA for a couple of years now with great success...This year I upgraded to the VXX esc and TX motors.
Howerver one of the VXX's seem to have a small issue....the red light is on all the time and altought I have steering and the esc fan works just fine when I aplly the trottle nothing happens!
Tried to setup the esc again...I have blue light but no sound and then again the same story...I even tried to reinstall the firmare but the programm cannot find the esc
Any ideas??
Howerver one of the VXX's seem to have a small issue....the red light is on all the time and altought I have steering and the esc fan works just fine when I aplly the trottle nothing happens!
Tried to setup the esc again...I have blue light but no sound and then again the same story...I even tried to reinstall the firmare but the programm cannot find the esc
Any ideas??
#7307
Team EAM
iTrader: (79)
I am running ORCA for a couple of years now with great success...This year I upgraded to the VXX esc and TX motors.
Howerver one of the VXX's seem to have a small issue....the red light is on all the time and altought I have steering and the esc fan works just fine when I aplly the trottle nothing happens!
Tried to setup the esc again...I have blue light but no sound and then again the same story...I even tried to reinstall the firmare but the programm cannot find the esc
Any ideas??
Howerver one of the VXX's seem to have a small issue....the red light is on all the time and altought I have steering and the esc fan works just fine when I aplly the trottle nothing happens!
Tried to setup the esc again...I have blue light but no sound and then again the same story...I even tried to reinstall the firmare but the programm cannot find the esc
Any ideas??
EA
#7311
I seen your 84 pitch gears. Do you have a conversion chart for comparing 84 vs 64?
I'm running 100/49 64p now. What would that be in 84p.
Thanks
Joe
I'm running 100/49 64p now. What would that be in 84p.
Thanks
Joe
#7313
Team EAM
iTrader: (79)
The formula is Teeth = (Outside diameter x pitch) -2
So 100 tooth is roughly 1.59375 inches.
(1.59375 x 64) = 102 subtract 2 = 100
So using this formula 100/49 in 84 pitch would be 132/65.
They do not have 65 teeth pinions yet, but 122/60 will give you the same ratio.
So 100 tooth is roughly 1.59375 inches.
(1.59375 x 64) = 102 subtract 2 = 100
So using this formula 100/49 in 84 pitch would be 132/65.
They do not have 65 teeth pinions yet, but 122/60 will give you the same ratio.
Joe,
Promod is exactly right. Thanks for posting the formula here! Also there is a chart on my FB page and also Leespeeds FB page.
They are making special USA pinions now in 61-92 Teeth so we can run in the blinky classes. Those are in production now and should be here in about 2 weeks.
Thanks
EA
#7318
Tech Apprentice
Trinity D4
____________________________________________
Alex Leeman
Team EAM
Progressive R/C
92zero Designs
#7319
Tech Master
iTrader: (32)
Thinking of picking up a 13.5T Orca TX. Can anyone confirm they are ROAR legal? I don't see them on the list, but I do see this:
http://roarracing.org/4rmb/showthrea...eries-OTM135TX
Thanks!
http://roarracing.org/4rmb/showthrea...eries-OTM135TX
Thanks!