57Likes

The Speed Passion Thread

Reply Subscribe

Thread Tools

Search this Thread

03-09-2011 | 11:52 PM

#6691

irgo

Tech Fanatic

Joined: Apr 2006

Posts: 893

Quote:

Originally Posted by striketun

Hi Guys!

I have SP 2.1 ProStock ESC and a SP 13.5 V3 motor.

Whats a good starting gear ration of this setting?

Thanks.

Download Manual for finding Starting point here
Official Speed Passion Website :
http://www.speedpassion.net/en/produ...802PROSb&c=ESC

03-10-2011 | 06:13 AM

#6692

mahamoti

Tech Regular

iTrader: (16)

Joined: Oct 2010

Posts: 387

From: Covington, LA

I too am looking for a good starting point for 12th scale 17.5 boosted with a 2.1EX and 17.5 V3 1 cell... I've been through the manuals, and haven't seen a recommendation for settings and rollout.

03-10-2011 | 06:36 AM

#6693

ewashburnaf

Tech Regular

iTrader: (14)

Joined: Sep 2010

Posts: 481

From: NC

so... still no prices on the new sportsman v3 motors?

03-11-2011 | 05:32 AM

#6694

mahamoti

Tech Regular

iTrader: (16)

Joined: Oct 2010

Posts: 387

From: Covington, LA

Quote:

Originally Posted by mahamoti

I too am looking for a good starting point for 12th scale 17.5 boosted with a 2.1EX and 17.5 V3 1 cell... I've been through the manuals, and haven't seen a recommendation for settings and rollout.

Also, what version firmware is best to use for this setup?

03-11-2011 | 02:55 PM

#6695

[[john]]

R/C Tech Elite Member

iTrader: (24)

Joined: Oct 2005

Posts: 869

From: Melbourne, Australia

Hi Guys!

Is the plastic bottom case available separately for the SP ProStock 2.1?

I have a few cracks in it

03-11-2011 | 09:36 PM

#6696

Solara

Tech Champion

iTrader: (17)

Joined: Sep 2002

Posts: 9,295

From: Chicago Illinois USA

Quote:

Originally Posted by ewashburnaf

so... still no prices on the new sportsman v3 motors?

Should be release soon...but should be around the same as the V2 motor.

03-11-2011 | 09:38 PM

#6697

Solara

Tech Champion

iTrader: (17)

Joined: Sep 2002

Posts: 9,295

From: Chicago Illinois USA

Quote:

Originally Posted by [[john]]

Hi Guys!

Is the plastic bottom case available separately for the SP ProStock 2.1?

I have a few cracks in it

Contact SP USA office and talk to the boss there and he will get you couple of those.

03-11-2011 | 11:17 PM

#6698

[[john]]

R/C Tech Elite Member

iTrader: (24)

Joined: Oct 2005

Posts: 869

From: Melbourne, Australia

Quote:

Originally Posted by Solara

Contact SP USA office and talk to the boss there and he will get you couple of those.

Even though I am located in Australia? I don't mind paying.

How would I go about getting in contact with him?

Thanks!

03-11-2011 | 11:26 PM

#6699

irgo

Tech Fanatic

Joined: Apr 2006

Posts: 893

Talk about case,

Solara, Will Speed Passion release Case gasket, for SP GT2.0 and GT2.1 ?
Shielded case or something like that...

ex: "Highly water-resistant case with protective silicone gasket"

03-12-2011 | 07:48 AM

#6700

thunderbt3

Tech Master

iTrader: (14)

Joined: Nov 2004

Posts: 1,087

I would highly doubt it. A sealed case would be useless since water can still get in the top through the sensor connector, switch and rx ports.

03-12-2011 | 08:17 AM

#6701

Atrick808

Tech Adept

iTrader: (11)

Joined: Oct 2010

Posts: 195

From: covington, la

Quote:

Originally Posted by mahamoti

I too am looking for a good starting point for 12th scale 17.5 boosted with a 2.1EX and 17.5 V3 1 cell... I've been through the manuals, and haven't seen a recommendation for settings and rollout.

I am looking for this information also!

03-12-2011 | 09:09 AM

#6702

irgo

Tech Fanatic

Joined: Apr 2006

Posts: 893

Quote:

Originally Posted by thunderbt3

I would highly doubt it. A sealed case would be useless since water can still get in the top through the sensor connector, switch and rx ports.

it works
as i found a disturbing sensored socket by flood of water, will result
only sensored disabled and switch to sensoreless.
no electricity shortage may cause burned. (safety technology)

Unless the one at the rx wire sockets and fan sockets.
and yes the switch wire.

03-12-2011 | 09:17 AM

#6703

Chubba

Tech Adept

Joined: Jun 2009

Posts: 174

From: Hong Kong

Hi there I am new to EP and I need to change the end/timing bell on my new sp 13.5T motor. How do I go about this?

Thanks

03-12-2011 | 09:36 AM

#6704

sidecarphil1

Tech Master

iTrader: (1)

Joined: Feb 2009

Posts: 1,920

Quote:

Originally Posted by Chubba

Hi there I am new to EP and I need to change the end/timing bell on my new sp 13.5T motor. How do I go about this?

Thanks

Loosen the 3 screws on the front of the motor , push slightly on them to loosen the rear end of the motor and move the sensor plug to 10 , i wouldnt advise running less then this as the movors get warm quickly and power is lower

dont forget to tighten the 3 screws BUT not too much

03-12-2011 | 09:37 AM

#6705

sidecarphil1

Tech Master

iTrader: (1)

Joined: Feb 2009

Posts: 1,920

hey guys i have the GT2.0Pro with the stock softwere in it and my question is i am trying out tomorrow with my 6.5 motor and i want to know if it is safe to run in this setting or should i switch back to the mod firmwere into it

Thanks Phil