Go Back  R/C Tech Forums > General Forums > Radio and Electronics
Get the most from a "spec" NiCD pack ? >

Get the most from a "spec" NiCD pack ?

Community
Wiki Posts
Search

Get the most from a "spec" NiCD pack ?

Thread Tools
 
Search this Thread
 
Old 05-19-2008 | 10:58 AM
  #1  
inconceivable's Avatar
Thread Starter
Tech Regular
iTrader: (3)
 
Joined: Jan 2008
Posts: 332
Default Get the most from a "spec" NiCD pack ?

A few months ago I began racing in a "spec" touring car class that includes hand out 2000Mah NiCD batteries (6 cell 7.2V). It has been a while since I really tried to get the most from these packs and have been struggling at each event. These are low grade, sport, NiCD batteries .... however it seems to me that others may be getting more from their batteries than I do (run time and punch). Anyway, I was curious if someone could help refresh my memory on the best way to charge and discharge. Thanks.
inconceivable is offline  
Old 05-21-2008 | 01:47 PM
  #2  
Cesar's Avatar
Tech Adept
iTrader: (1)
 
Joined: Aug 2005
Posts: 136
Default

U got pm
Cesar is offline  
Old 05-23-2008 | 01:33 PM
  #3  
Tech Champion
 
Joined: Oct 2007
Posts: 7,341
Default

In general nicads need to be discharged all the way every time, right after your run. Not familiar with that battery, but I would suggest discharging at 20 amps, maybe more. At least with the 1200-1700 Sanyo nicads I used back in the day, discharging them at a high rate increased voltage under load after a few cycles. What was called pushing or training. Which is where matching cells started I believe, so you could discharge hard without damaging weaker cells.

And the higher you charge them, the better the punch will be as well. Suggest a 6 amp charge, try to have them peak about 10-15 minutes before the race, then repeak at 8 amps right before hitting the track. Or higher at the risk of reduced run time and battery life, but more punch.

Store them discharged. Some would dead short them before charging, but I think that depended on which nicad. I discharged to 0.5 volt per cell with good results.

Of course with all of this weak cells do not survive. If I remember correctly back in the day my battery matcher would start with 5 cycles to train them before matching, and some didn't survive. But the ones that did performed much better. So I guess if you can't open the packs to rematch you might have to lower the amperage some, but at least be sure to discharge them all the way every time.
Good luck!
Dave H is offline  
Old 05-23-2008 | 02:36 PM
  #4  
inconceivable's Avatar
Thread Starter
Tech Regular
iTrader: (3)
 
Joined: Jan 2008
Posts: 332
Default

Very helpful info .... Thanks !
inconceivable is offline  
Old 05-23-2008 | 08:45 PM
  #5  
Cesar's Avatar
Tech Adept
iTrader: (1)
 
Joined: Aug 2005
Posts: 136
Default

I was always told never to discharge nicads past .7v per cell, due to cell reversal (polarity flips-creates a short). Nimh (up to GP3700) were able to be stored with a dead short prior to the IB cells that showed up. When the IB Cells took over people started to dead short and were not able to get batteries back to charge. Follow this link to learn more about batteries.

Hope this helps,
Cesar
Cesar is offline  

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.