R/C Tech Forums

Go Back  R/C Tech Forums > General Forums > Monster Trucks
Tekno MT410 >

Tekno MT410

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
Like Tree396Likes

Tekno MT410

Thread Tools
 
Search this Thread
 
Old 02-25-2017 | 11:32 AM
  #526  
vettehigh's Avatar
vettehigh
Tech Addict
iTrader: (4)
 
Joined: Feb 2017
Posts: 686
From: Upstate, NY
Default
T-Bone Racing has the wheelie bar too
vettehigh is offline  
Reply
Old 02-25-2017 | 01:56 PM
  #527  
teeforb's Avatar
teeforb
Tech Champion
iTrader: (94)
 
Joined: Sep 2005
Posts: 7,298
From: San Diego & Compton CA
Default
Have you considered the hobbywing xr8 combo?

Originally Posted by vettehigh
I going to pull the trigger on the Tekno, but I need to figure out my motor/esc choice?

So far these are it:

(#TT2325) - Tekin 1/8 RX8 Gen2 Brushless ESC/4038 Motor 2250kV ($309)
(#010-0145-01) - Castle Creations 1/8 Mamba Monster X WP ESC/2200kV ($239)
(#010-0139-00) - Castle Creations 1/8 Sidewinder 8th ESC + 2200kV Motor ($159)

Here are my other items:
Tekno RC Pinion Gear 15T M5(MOD1/5mm Bore/M5 Set Scrw)
Tekno RC Spur Gear 44T Hardened Stl/Lghtd/EB48/SCT410
Tekno RC Aluminum Servo Horn Double Hole 24T Spline
Hitec HS-7950TH HV Ultra-Torque Titanium Corless Servo
Tekno RC Shock Cap Aluminum EB48/SCT410
Tekno RC Steering Servo Brace EB48/SCT410
DE Racing XD Rear Skid Plate Tekno RC EB48/SCT410
Pro-Line Shockwave 3.8" MT Mtd F-11 17mm F/R
Pro-Line Extended Front/Rear Body Mounts SCT410
Futaba 3PRKA 3-Channel FHSS System
teeforb is offline  
Reply
Old 02-25-2017 | 02:09 PM
  #528  
vettehigh's Avatar
vettehigh
Tech Addict
iTrader: (4)
 
Joined: Feb 2017
Posts: 686
From: Upstate, NY
Default
Originally Posted by teeforb
Have you considered the hobbywing xr8 combo?
I have not yet. Is that the combo for $279 and do you have a link? You would chose that combo? This will be my final project for years to come (will use on certain spring/summer weekends), so I want to do it right with no regrets.
vettehigh is offline  
Reply
Old 02-25-2017 | 02:13 PM
  #529  
teeforb's Avatar
teeforb
Tech Champion
iTrader: (94)
 
Joined: Sep 2005
Posts: 7,298
From: San Diego & Compton CA
Default
Originally Posted by vettehigh
I have not yet. Is that the combo for $279? You would chose that combo? This will be my final project for years to come (will use on certain spring/summer weekends), so I want to do it right with no regrets.
I run it in my mt410. Ill post link to video
teeforb is offline  
Reply
Old 02-25-2017 | 02:14 PM
  #530  
teeforb's Avatar
teeforb
Tech Champion
iTrader: (94)
 
Joined: Sep 2005
Posts: 7,298
From: San Diego & Compton CA
Default
https://youtu.be/cjhHF6U0tr8
teeforb is offline  
Reply
Old 02-25-2017 | 02:17 PM
  #531  
teeforb's Avatar
teeforb
Tech Champion
iTrader: (94)
 
Joined: Sep 2005
Posts: 7,298
From: San Diego & Compton CA
Default
https://www.amainhobbies.com/hobbywi...020407/p520598
teeforb is offline  
Reply
Old 02-25-2017 | 02:21 PM
  #532  
vettehigh's Avatar
vettehigh
Tech Addict
iTrader: (4)
 
Joined: Feb 2017
Posts: 686
From: Upstate, NY
Default
Thank you, so you would pick that over my 3 motor/esc combos?
vettehigh is offline  
Reply
Old 02-25-2017 | 03:49 PM
  #533  
teeforb's Avatar
teeforb
Tech Champion
iTrader: (94)
 
Joined: Sep 2005
Posts: 7,298
From: San Diego & Compton CA
Default
Originally Posted by vettehigh
Thank you, so you would pick that over my 3 motor/esc combos?
Yes! For sure. Tekin would be my second choice.

I had them all. HW is by far my favorite in terms of quality and reliability. That combo I suggested is a BEAST in the mt410. Motor temps are around 140 deg after hard bashing. With that combo, 17t was too much power. I found 15t pinion was perfect!
teeforb is offline  
Reply
Old 02-26-2017 | 06:46 AM
  #534  
vettehigh's Avatar
vettehigh
Tech Addict
iTrader: (4)
 
Joined: Feb 2017
Posts: 686
From: Upstate, NY
Questions??
Originally Posted by teeforb
Yes! For sure. Tekin would be my second choice.

I had them all. HW is by far my favorite in terms of quality and reliability. That combo I suggested is a BEAST in the mt410. Motor temps are around 140 deg after hard bashing. With that combo, 17t was too much power. I found 15t pinion was perfect!
Just to make sure, that's part #38020407

They seem to be out of stock everywhere
vettehigh is offline  
Reply
Old 02-26-2017 | 03:49 PM
  #535  
vettehigh's Avatar
vettehigh
Tech Addict
iTrader: (4)
 
Joined: Feb 2017
Posts: 686
From: Upstate, NY
Questions??
Is getting the TKR5298 Universal Driveshaft Set (2 or 4 total pieces?) worth it? Think you need TKRBB08165 Ball Bearings (8x16x5, 4pcs) too...
Last edited by vettehigh; 02-26-2017 at 05:42 PM.
vettehigh is offline  
Reply
Old 02-26-2017 | 04:38 PM
  #536  
teeforb's Avatar
teeforb
Tech Champion
iTrader: (94)
 
Joined: Sep 2005
Posts: 7,298
From: San Diego & Compton CA
Default
Originally Posted by vettehigh
Just to make sure, that's part #38020407

They seem to be out of stock everywhere
Yes correct
teeforb is offline  
Reply
Old 02-26-2017 | 07:45 PM
  #537  
teeforb's Avatar
teeforb
Tech Champion
iTrader: (94)
 
Joined: Sep 2005
Posts: 7,298
From: San Diego & Compton CA
Default
Originally Posted by vettehigh
Is getting the TKR5298 Universal Driveshaft Set (2 or 4 total pieces?) worth it? Think you need TKRBB08165 Ball Bearings (8x16x5, 4pcs) too...
There are a lot of them in stock on eBay.
teeforb is offline  
Reply
Old 02-27-2017 | 08:38 AM
  #538  
vettehigh's Avatar
vettehigh
Tech Addict
iTrader: (4)
 
Joined: Feb 2017
Posts: 686
From: Upstate, NY
Questions??
Originally Posted by vettehigh
Is getting the TKR5298 Universal Driveshaft Set (2 or 4 total pieces?) worth it? Think you need TKRBB08165 Ball Bearings (8x16x5, 4pcs) too...
Just spoke with Tekno, these are not needed. Just going with the alum servo horn and steel spur gear. As for body mount posts, I was looking into Pro-Line Racing 6272-00 Extended Front/Rear Body Mounts...are these a good fit?
vettehigh is offline  
Reply
Old 02-27-2017 | 09:07 AM
  #539  
ezlight
Tech Master
 
Joined: Oct 2014
Posts: 1,167
From: Maine
Default
Originally Posted by vettehigh
4S only

What motor/esc would you recommend? As for the radio, only want the basic.
If your not worried about being waterproof, and guessing your not since only 1 of your options were Wp, Check out

RF-150-8PB

And either of these

http://www.smc-racing.net/index.php?...y&path=112_125

I've been running both in my ET48.3 paired with the 1900kv buggy motor and an 18t pinion. I'm guessing to make up for the MT tire size, you may want a 17t pinion. Or go with the 2100kv and be in the 16t range?
ezlight is offline  
Reply
Old 02-28-2017 | 09:25 AM
  #540  
vettehigh's Avatar
vettehigh
Tech Addict
iTrader: (4)
 
Joined: Feb 2017
Posts: 686
From: Upstate, NY
Default My final list
This is my final build list and my overall cost will be around $1200+ complete

*Badhorsie shock covers
*T-Bone Racing front bumper and wheelie bar
*Bigfoot custom painted body (Proline 3252-00 Ford F-250 MT body)
*Gens ace 5000mAh 14.8V 50C 4S1P HardCase Lipo

Tekno RC 1/10 MT410 Pro 4x4 Kit
Hobbywing Xerun XR8 Plus Brushless ESC/G2 Motor Combo (2250kV)
Tekno RC Pinion Gear 15T M5(MOD1/5mm Bore/M5 Set Scrw)
Tekno RC Spur Gear 44T Hardened Stl/Lghtd/EB48/SCT410
Tekno RC Aluminum Servo Horn Double Hole 24T Spline
Hitec HS-7950TH HV Ultra-Torque Titanium Corless Servo
Tekno RC Shock Cap Aluminum
Tekno RC Steering Servo Brace
DE Racing XD Rear Skid Plate Tekno RC
Tekno RC Rear Arm Mud Guard
Tekno RC CNC Delrin Shock Cartridge Set
Pro-Line Shockwave 3.8" MT Mtd F-11 17mm F/R
Futaba 3PRKA 3-Channel FHSS System
Pro-Line Extended Front/Rear Body Mounts
Tekno RC Wheel Nuts T Logo 17mm Serrated M12x1.0
vettehigh is offline  
Reply



Advanced Search

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.