VBC Racing D08
#481
I can get the d08 dynamics still.
I have an order that is about to ship from hk soon let me know
[email protected]
I have an order that is about to ship from hk soon let me know
[email protected]
I had asked you about an 08 kit before I bought this one. Wanted the cheap deal. Did the Dynamics go on clearance?
#482
#483
The castor blocks from xray are not a direct fit, i never said they were. You will need to change the sleeve to xray sleeves and some sanding and shimming. I know this because ive used them before. Modification of your ride is not a crime, ive seen plenty of pro drivers using products outside of their sponsors. If you think using a different part will make you faster then do it.
#484
DO8 BELTS
Hi guys dose anyone know if any other brand of belts fit the D08
Thank you
Thank you
#485
Tech Fanatic
#486
#487
Tech Elite
iTrader: (29)
if you're having issues with c hubs and you have not sanded the wheel axle ends, I highly recommend it.
click trak and other track walls with gaps between sections will cause damage at some point.
sand them down until they're about 2mm from the hex, then round them so they'll "skip" through the cracks when you decide to rub the walls.
a dremel with the sanding drum is great for this.
click trak and other track walls with gaps between sections will cause damage at some point.
sand them down until they're about 2mm from the hex, then round them so they'll "skip" through the cracks when you decide to rub the walls.
a dremel with the sanding drum is great for this.
#488
D09 chassis
Has anyone run aD09 chassis on a d08 yet if so was it any good
#489
#490
#492
If you managed to just screw this on without modifying, I'd like to see it, as I just don't see it being a straight swap.
#493
Tech Addict
iTrader: (2)
I have overlayed the D08 to the D09 chassis, and without modifying the existing D08 mount, it will not work. Besides having to either remove the locating pins from the mount or drilling the D09 chassis for the pins it won't work. Even if this is done, only one screw will line up properly and the forward mount screw will be 1.47mm out of place. I guess you could try running with just one screw holding the mount in place, or force the forward screw in, but then you'll have a bowed chassis. Also without drilling additional holes, you'll loose the ability to add extra screws for flex settings.
If you managed to just screw this on without modifying, I'd like to see it, as I just don't see it being a straight swap.
If you managed to just screw this on without modifying, I'd like to see it, as I just don't see it being a straight swap.
That's NOT a good news!!! LOL
Anyone swap out the ball cups with any other companies? around here VBC does not exist.. I hoping associated will work, since I have used 5mm ballstuds.
Last edited by 1shnot; 01-25-2017 at 04:41 PM.
#494
I have overlayed the D08 to the D09 chassis, and without modifying the existing D08 mount, it will not work. Besides having to either remove the locating pins from the mount or drilling the D09 chassis for the pins it won't work. Even if this is done, only one screw will line up properly and the forward mount screw will be 1.47mm out of place. I guess you could try running with just one screw holding the mount in place, or force the forward screw in, but then you'll have a bowed chassis. Also without drilling additional holes, you'll loose the ability to add extra screws for flex settings.
If you managed to just screw this on without modifying, I'd like to see it, as I just don't see it being a straight swap.
If you managed to just screw this on without modifying, I'd like to see it, as I just don't see it being a straight swap.
With photos
#495
3 racing ones fit perfectly, they have the same size ball cups, in dirrerent colours, red looks really good on this chassis