R/C Tech Forums

Go Back  R/C Tech Forums > General Forums > Electric Off-Road
JConcepts Thread >

JConcepts Thread

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
Like Tree495Likes

JConcepts Thread

Thread Tools
 
Search this Thread
 
Old 06-14-2015 | 08:24 PM
  #8431  
jk racing's Avatar
jk racing
Tech Elite
iTrader: (20)
 
Joined: Aug 2004
Posts: 2,731
From: Placentia, CA
Default
Originally Posted by Brandon Powell
need a small pin sc 4x4 tire between double dees and pressure points. Recommendations? Loamy, wet outdoor
3Ds?
jk racing is offline  
Reply
Old 06-15-2015 | 01:44 PM
  #8432  
PW's Avatar
PW
Tech Elite
 
Joined: Sep 2001
Posts: 4,786
From: Groveland, FL
Default
Originally Posted by mes
Is it too early to say if the Team Associated SC5M will run the +3 Hazard wheels #3344 or the #3352s?
It has already been discussed, it is going to use zero offset wheels.
I spoke with Team Associated and the truck is the same width as the SC10, which means you will still need the +3 Hazards to make it max width (ROAR).

need a small pin sc 4x4 tire between double dees and pressure points. Recommendations? Loamy, wet outdoor
I would recommend the Lil Chasers - Click Here

PW is offline  
Reply
Old 06-15-2015 | 05:00 PM
  #8433  
Micah123
Tech Addict
iTrader: (1)
 
Joined: May 2012
Posts: 590
Default
Originally Posted by Micah123
They came with dirt techs. Previous set came with blue foams that worked fine but new dirt techs are way firm for stadium truck tires. Run at sdrc in san diego which has very good traction. thanks for the input. was planning on 1 hole per rib but will compare 1,2,and 3 before re gluing. thanks again.
Went with 3 holes per rib and still plenty firm. Wondering if I should cut down ribs to soften more. Feel free to chime in if you have already been thru this process. Will not glue until tomorrow.
Micah123 is offline  
Reply
Old 06-15-2015 | 05:36 PM
  #8434  
aeRayls's Avatar
aeRayls
Tech Elite
iTrader: (3)
 
Joined: Nov 2007
Posts: 2,257
Default
Originally Posted by Micah123
Went with 3 holes per rib and still plenty firm. Wondering if I should cut down ribs to soften more. Feel free to chime in if you have already been thru this process. Will not glue until tomorrow.
DO NOT cut the truck foams!!! They will be way too small! I've already done it. Just mount em with the holes and run em. They will break in!
aeRayls is offline  
Reply
Old 06-15-2015 | 07:58 PM
  #8435  
Micah123
Tech Addict
iTrader: (1)
 
Joined: May 2012
Posts: 590
Default
thank you sir. seems like 3 holes per rib is just about right. appreciate the input.
Micah123 is offline  
Reply
Old 06-29-2015 | 09:12 AM
  #8436  
KAWIDAD's Avatar
KAWIDAD
Tech Addict
iTrader: (24)
 
Joined: Jul 2013
Posts: 626
From: Oviedo, Fl
Default B5M Bodies
What are the different handling characteristics for the finisher and silencer?
Running a FL w/17.5 (if that matters)
Thanks
KAWIDAD is offline  
Reply
Old 06-29-2015 | 09:16 AM
  #8437  
PW's Avatar
PW
Tech Elite
 
Joined: Sep 2001
Posts: 4,786
From: Groveland, FL
Default
Originally Posted by KAWIDAD
What are the different handling characteristics for the finisher and silencer?
Running a FL w/17.5 (if that matters)
Thanks
I personally think it's more mental then anything, but the Silencer is thought to be a little smoother and more locked in. The Finnisher is a little freer, more rotation.
PW is offline  
Reply
Old 06-29-2015 | 09:22 AM
  #8438  
flintTRDTC
Tech Regular
iTrader: (20)
 
Joined: Apr 2013
Posts: 377
From: Whittier CA
Arrow
PW - I haven't seen this question asked yet on the soon to be released SC5m, but do we know if the current line of JC SC bodies are a direct fit with the current body mount holes or have they been moved to accommodate the mid motor setup. Thanks in advance.
flintTRDTC is offline  
Reply
Old 06-29-2015 | 09:29 AM
  #8439  
Wildcat1971's Avatar
Wildcat1971
Tech Prophet
iTrader: (84)
 
Joined: Apr 2012
Posts: 17,389
From: Arizona
Default
any plans on 2.2 smoothies?
Wildcat1971 is offline  
Reply
Old 06-29-2015 | 09:46 AM
  #8440  
PW's Avatar
PW
Tech Elite
 
Joined: Sep 2001
Posts: 4,786
From: Groveland, FL
Default
Originally Posted by flintTRDTC
PW - I haven't seen this question asked yet on the soon to be released SC5m, but do we know if the current line of JC SC bodies are a direct fit with the current body mount holes or have they been moved to accommodate the mid motor setup. Thanks in advance.
Good question; I don't know and will have to find out. We unfortunately don't have a kit yet to check body mount placement.

any plans on 2.2 smoothies?
It's in discussion, but nothing yet.
PW is offline  
Reply
Old 06-29-2015 | 01:18 PM
  #8441  
PW's Avatar
PW
Tech Elite
 
Joined: Sep 2001
Posts: 4,786
From: Groveland, FL
Default
Originally Posted by flintTRDTC
PW - I haven't seen this question asked yet on the soon to be released SC5m, but do we know if the current line of JC SC bodies are a direct fit with the current body mount holes or have they been moved to accommodate the mid motor setup. Thanks in advance.
Spoke with AE and they said the front mounts are the same, but unfortunately the rear mounts are further back compared to the SC10.2
PW is offline  
Reply
Old 06-29-2015 | 01:23 PM
  #8442  
hollywood3705's Avatar
hollywood3705
Tech Addict
iTrader: (10)
 
Joined: Nov 2014
Posts: 540
Default
Any thoughts on the current trend of 60mm tires and wheels? By that I mean do you perceive it as a tuning options or the next way all tires will be. No one can seem to agree so far but I've also noticed no new tires in 2.2. Any insight as the the direction paul?
hollywood3705 is offline  
Reply
Old 06-29-2015 | 01:36 PM
  #8443  
PW's Avatar
PW
Tech Elite
 
Joined: Sep 2001
Posts: 4,786
From: Groveland, FL
Default
Originally Posted by hollywood3705
Any thoughts on the current trend of 60mm tires and wheels? By that I mean do you perceive it as a tuning options or the next way all tires will be. No one can seem to agree so far but I've also noticed no new tires in 2.2. Any insight as the the direction paul?
I personally think it will continue to be a tuning option unfortunately. Truthfully it's not an option that was really needed, but now its here along with the added cost and confusion .
PW is offline  
Reply
Old 06-29-2015 | 03:03 PM
  #8444  
flintTRDTC
Tech Regular
iTrader: (20)
 
Joined: Apr 2013
Posts: 377
From: Whittier CA
Default
Originally Posted by PW
Spoke with AE and they said the front mounts are the same, but unfortunately the rear mounts are further back compared to the SC10.2
Thanks Paul.
flintTRDTC is offline  
Reply
Old 06-29-2015 | 07:59 PM
  #8445  
hollywood3705's Avatar
hollywood3705
Tech Addict
iTrader: (10)
 
Joined: Nov 2014
Posts: 540
Default
I sadly agree...just wish jcon would offer some of the newer tire patterns in 2.2
I know it's crazy cost but just a thought.
Thanks paul
hollywood3705 is offline  
Reply



Advanced Search

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.