Community
Wiki Posts
Search

fix a shorted lipo

Thread Tools
 
Search this Thread
 
Old 06-16-2014 | 05:20 PM
  #1  
Thread Starter
Tech Adept
 
Joined: Feb 2013
Posts: 108
Default fix a shorted lipo

Is there any way to fix a lipo that was shorted?
I just got a few turnigy 2s lipos, and I wasn't thinking at all when I cut off the stock connector on one to solder on my deans. I just cut the pos and neg at the same time, which obviously caused a short. it was just for a split second, but it was long enough I guess to probably melt the connector for one of the cells. Checked the voltage of each cell, one reads 4.18, the other doesn't read anything.

I'm pretty sure it's trash, but hoping there might be some secret to fix it
Dynikus is offline  
Old 06-17-2014 | 12:06 AM
  #2  
Tech Elite
iTrader: (17)
 
Joined: Apr 2009
Posts: 3,055
Default

Most of these have a small board with thin traces designed to pop when shorted. Sometimes it is possible to run a dab of solder across the broken trace. I have fixed a few like this.
burnineyes is offline  
Old 06-17-2014 | 02:46 AM
  #3  
Thread Starter
Tech Adept
 
Joined: Feb 2013
Posts: 108
Default

can you possibly post a pic of what you mean? does it require opening the battery?
Dynikus is offline  
Old 06-17-2014 | 02:59 AM
  #4  
Hoese37's Avatar
Tech Elite
iTrader: (5)
 
Joined: Apr 2007
Posts: 3,819
From: Hutchinson, MN
Default

Yes you have to get inside the battery. Most likely you broke a solder tab. It's very hard to solder because a lot of them are aluminum.
Hoese37 is offline  
Old 06-17-2014 | 04:54 AM
  #5  
dan_vector's Avatar
Tech Elite
iTrader: (27)
 
Joined: Oct 2013
Posts: 4,333
Default

Is it really advisable to open a hard case lipo?? Hmmm I don't think I would do it and at the price of a turnigy pack it's cheap enough to toss (learning from the costly error!) and buy new. Certainly wouldn't want to risk burning my house down!
dan_vector is offline  
Old 06-17-2014 | 06:03 AM
  #6  
Darkgenerals's Avatar
R/C Tech Elite Member
iTrader: (82)
 
Joined: Jul 2013
Posts: 1,663
From: Granbury Tx
Default

Originally Posted by Hoese37
Yes you have to get inside the battery. Most likely you broke a solder tab. It's very hard to solder because a lot of them are aluminum.
Originally Posted by dan_vector
Is it really advisable to open a hard case lipo?? Hmmm I don't think I would do it and at the price of a turnigy pack it's cheap enough to toss (learning from the costly error!) and buy new. Certainly wouldn't want to risk burning my house down!
+2

Unless your really good at soldering, like freaky good at soldering, I would not suggest messing with the inside of a lipo. If you do it, please do it outside in a well ventilated area, with a bucket of sand near by.
Darkgenerals is offline  
Old 06-17-2014 | 06:58 AM
  #7  
dan_vector's Avatar
Tech Elite
iTrader: (27)
 
Joined: Oct 2013
Posts: 4,333
Default

I'm freaky good at soldering and even I wouldn't attempt it.
dan_vector is offline  
Old 06-17-2014 | 10:14 AM
  #8  
Thread Starter
Tech Adept
 
Joined: Feb 2013
Posts: 108
Default

I would never open up a lipo over a $25 battery, to my understanding lipos are dangerous mofos.
I'm sure I'll never make that mistake again atleast
Dynikus is offline  
Old 06-17-2014 | 10:25 AM
  #9  
lbenton's Avatar
Tech Elite
iTrader: (48)
 
Joined: Aug 2012
Posts: 2,127
From: Fort Worth Tx
Default

Originally Posted by Dynikus
to my understanding lipos are dangerous mofos.
Only if they are shorted / damaged or over-taxed.

It is the standard power in so many devices not just our cars.
lbenton is offline  
Old 06-17-2014 | 11:25 AM
  #10  
Tech Adept
 
Joined: Mar 2012
Posts: 183
From: The Netherlands
Default

Originally Posted by lbenton
Only if they are shorted / damaged or over-taxed.

It is the standard power in so many devices not just our cars.
I've unfortunately seen one explode firsthand, while it wasn't doing anything special other than powering an F1 R/C car. Even with normal usage: always charge in a safety bag.
Thaan is offline  
Old 06-17-2014 | 04:12 PM
  #11  
phildoggg's Avatar
Tech Addict
iTrader: (24)
 
Joined: Feb 2009
Posts: 676
From: N.C.
Default

I'm with burning eyes, its prob the trace he spoke of. I've used solder braid to repair one before.
phildoggg is offline  
Old 06-17-2014 | 04:26 PM
  #12  
asc6000's Avatar
Tech Elite
iTrader: (15)
 
Joined: Jan 2011
Posts: 3,411
From: Meridian Idaho
Default

Get a new battery, small price to pay for a lesson learned.
asc6000 is offline  

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.