Arizona RC Swap Meet
#4519
Still have it and found another fuel tank that will go with it price reduced to 180$
#4522
Tech Prophet
iTrader: (84)
I have an SC10 for sale. I will include some spares as well
- front and rear hexes
- lunsford TI Turnbuckles.
- Ceramic diff balls and thrust balls
- VTS slipper
- Big bore spring conversion
- Avid Alum rack
- .5 and 1 deg alum FT rear hubs
- High Speed High Voltage servo
- RPM front and rear arms
- RPM ball cups
- CVDs
- Alum servo mounts
- FT blue shock mounts
- Alum front pin brace
The truck is not all beat down with stripped screws. It is in very good overall condition. I also have the parts to convert it into a T4 (chassis, body mounts, body, front bumper)
I would like $140 for everything including the spares. I also have the t4 hex axles in a parts bag. This is pretty much everything i have for the sc10/t4. I will include a sc10 and t4 body also and every single hex sc tire I own. And you can have the t4 pin/bearing wheels also is you like. I just want everything out of my garage.
- front and rear hexes
- lunsford TI Turnbuckles.
- Ceramic diff balls and thrust balls
- VTS slipper
- Big bore spring conversion
- Avid Alum rack
- .5 and 1 deg alum FT rear hubs
- High Speed High Voltage servo
- RPM front and rear arms
- RPM ball cups
- CVDs
- Alum servo mounts
- FT blue shock mounts
- Alum front pin brace
The truck is not all beat down with stripped screws. It is in very good overall condition. I also have the parts to convert it into a T4 (chassis, body mounts, body, front bumper)
I would like $140 for everything including the spares. I also have the t4 hex axles in a parts bag. This is pretty much everything i have for the sc10/t4. I will include a sc10 and t4 body also and every single hex sc tire I own. And you can have the t4 pin/bearing wheels also is you like. I just want everything out of my garage.
Last edited by Wildcat1971; 02-05-2014 at 09:32 AM.
#4523
K, curious ehames005, about the b4.2, any more info?
#4527
I know its not a car but up for sale is my Blade 350QX Quadcopter RTF with a Fatshark Predator V2 setup already installed and ready to go. The Quad has about 10 flights on it and has never been crashed or abused. This has had the newest props with the revision from horizon hobby. This really is a easy flyer and is a whole new experience when flying in FPV. Incase your not familiar with it it has GPS, barometer, and S.A.F.E. flight technology with 3 flight modes. It is also easily capable of carrying a Gopro on it for some awesome aerial filming (go pro mount is included). The goggle system allows you to fly in first person view which is an amazing feeling and whole new flight experience. It will come with the following:
Blade 350QX RTF: Includes radio, battery, charger ETC. Has everything it would come with new (i.e. spare props, manual, go pro mount, etc)
Extras:
2700mah 3s lipo for longer flight time
Fatshark Predator V2 FPV goggle system installed (includes goggles, TX/RX for video, battery and CCD camera)
Upgraded Spironet Antennas for longer range and clearer signal for the goggles.
Price is $700 which is FAR less than you would spend to get this setup new. Best of all it is all pre installed and test flown for you. I am only selling to put towards a 4wd buggy setup so cash only no trades. Thanks.
If interested call or text 575-491-1899.
Blade 350QX RTF: Includes radio, battery, charger ETC. Has everything it would come with new (i.e. spare props, manual, go pro mount, etc)
Extras:
2700mah 3s lipo for longer flight time
Fatshark Predator V2 FPV goggle system installed (includes goggles, TX/RX for video, battery and CCD camera)
Upgraded Spironet Antennas for longer range and clearer signal for the goggles.
Price is $700 which is FAR less than you would spend to get this setup new. Best of all it is all pre installed and test flown for you. I am only selling to put towards a 4wd buggy setup so cash only no trades. Thanks.
If interested call or text 575-491-1899.
#4528
Tech Initiate
iTrader: (2)
I tried to get back into RC, but couldn't and seemingly waited too long to sell off my stuff, but here it is anyways. All items have maybe ten races (qualifying and main heats) total on them unless otherwise stated.
FS:
Tekin Redline Gen 2 motor - $75
Airtronics 94770 servo - $65
HiTec X1 Ac charger - $50
Airtronics MT-4 radio & receiver + case with pre-cut foam - $250
FS:
Tekin Redline Gen 2 motor - $75
Airtronics 94770 servo - $65
HiTec X1 Ac charger - $50
Airtronics MT-4 radio & receiver + case with pre-cut foam - $250
Last edited by Haboob; 02-10-2014 at 06:02 AM.
#4530
Tech Prophet
iTrader: (84)
I have an SC10 for sale. I will include some spares as well
- front and rear hexes
- lunsford TI Turnbuckles.
- Ceramic diff balls and thrust balls
- VTS slipper
- Big bore spring conversion
- Avid Alum rack
- .5 and 1 deg alum FT rear hubs
- High Speed High Voltage servo
- RPM front and rear arms
- RPM ball cups
- CVDs
- Alum servo mounts
- FT blue shock mounts
- Alum front pin brace
The truck is not all beat down with stripped screws. It is in very good overall condition. I also have the parts to convert it into a T4 (chassis, body mounts, body, front bumper)
I would like $140 for everything including the spares. I also have the t4 hex axles in a parts bag. This is pretty much everything i have for the sc10/t4. I will include a sc10 and t4 body also and every single hex sc tire I own. And you can have the t4 pin/bearing wheels also is you like. I just want everything out of my garage.
- front and rear hexes
- lunsford TI Turnbuckles.
- Ceramic diff balls and thrust balls
- VTS slipper
- Big bore spring conversion
- Avid Alum rack
- .5 and 1 deg alum FT rear hubs
- High Speed High Voltage servo
- RPM front and rear arms
- RPM ball cups
- CVDs
- Alum servo mounts
- FT blue shock mounts
- Alum front pin brace
The truck is not all beat down with stripped screws. It is in very good overall condition. I also have the parts to convert it into a T4 (chassis, body mounts, body, front bumper)
I would like $140 for everything including the spares. I also have the t4 hex axles in a parts bag. This is pretty much everything i have for the sc10/t4. I will include a sc10 and t4 body also and every single hex sc tire I own. And you can have the t4 pin/bearing wheels also is you like. I just want everything out of my garage.