Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: Kelseyrc
Showing results 1 to 25 of 176
Search took 0.03 seconds.
05-17-2019, 10:48 AM
Replies: 14
Views: 2,068
Posted By Kelseyrc

I only run drag brake in mod (around 20%-25%) in...

I only run drag brake in mod (around 20%-25%) in order to get the weight over the front wheels to get more turn in. Especially in high grip tracks. For stock classes I don't find any need for it.
05-15-2019, 07:14 PM
Replies: 1
Views: 219
Posted By Kelseyrc

For 2wd, a lot of people run cactus and cut...

For 2wd, a lot of people run cactus and cut staggers in yellow compound. And for 4wd cactus and cactus fusions in yellow or prisms front and rear in z3 compound.
05-15-2019, 01:43 PM
Replies: 2,879
Views: 479,001
Posted By Kelseyrc

Yeah, I would say slipper eliminator and aluminum...

Yeah, I would say slipper eliminator and aluminum timing and stator screws. For smaller gains, titanium top shaft, plastic pinion. Everything else that I can think of would be more expensive (i.e....
05-10-2019, 02:11 PM
Replies: 16
Views: 622
Posted By Kelseyrc

And also keep in mind that the handling of the...

And also keep in mind that the handling of the car will be completely different if changing the orientation of the motor. This is due to the fact that the motor will be spinning the opposite...
05-10-2019, 02:02 PM
Replies: 16
Views: 622
Posted By Kelseyrc

Not sure what type of RC car you are running but...

Not sure what type of RC car you are running but in order to reverse the motor you will need to add another idler gear to change the rotation. In a 2wd buggy like a b6.1, you can accomplish this with...
Forum: Rookie Zone
04-24-2019, 02:41 PM
Replies: 9
Views: 371
Posted By Kelseyrc

You will need to tin the connector's solder posts...

You will need to tin the connector's solder posts as well in order for the solder joint to be solid. What I do is I hold the tinned-wire (with pliers) in the pre-tinned connector post and hold the...
04-10-2019, 01:35 PM
Replies: 3
Views: 207
Posted By Kelseyrc

I have a 419xr with spare parts that I am not...

I have a 419xr with spare parts that I am not using anymore. I raced it last summer season and at a TCS regional so it is Tamiya only. I am looking for $275 shipped to Con US. PM me if interested.
03-20-2019, 02:10 PM
Replies: 10
Views: 765
Posted By Kelseyrc

Something that I find really handy is an electric...

Something that I find really handy is an electric screwdriver with a 2 mm speed bit. It makes screwing in those screws that are 12mm+ a lot easier and quicker.
03-08-2019, 04:37 PM
Replies: 2,879
Views: 479,001
Posted By Kelseyrc

The only other thing is the ball diff that comes...

The only other thing is the ball diff that comes with the 6.1d
02-24-2019, 12:27 AM
Replies: 2,879
Views: 479,001
Posted By Kelseyrc

Rc speed secrets has the gears for a reasonable...

Rc speed secrets has the gears for a reasonable price
02-21-2019, 08:01 PM
Replies: 2,879
Views: 479,001
Posted By Kelseyrc

Oh yeah you are correct about the anti squat...

Oh yeah you are correct about the anti squat being 1*
02-21-2019, 07:51 PM
Replies: 2,879
Views: 479,001
Posted By Kelseyrc



02-21-2019, 07:50 PM
Replies: 2,879
Views: 479,001
Posted By Kelseyrc

That would be 2* of toe in and .5* of anti-squat....

That would be 2* of toe in and .5* of anti-squat. When using the center pill on both the c and d blocks the buggy has 3* of toe in and 0* of anti squat.
02-18-2019, 01:12 PM
Replies: 167
Views: 38,349
Posted By Kelseyrc

I run 78/26 on my XB4. This is with the Reedy S...

I run 78/26 on my XB4. This is with the Reedy S Plus, if you have a non high rpm motor you can go up a couple of teeth on you pinion
02-12-2019, 01:20 PM
Replies: 13,099
Views: 1,962,428
Posted By Kelseyrc

That seems really hot based on your gearing. With...

That seems really hot based on your gearing. With my setup the Reedy only gets up to around 135*. Have you checked to see if anything is binding in your drivetrain?
02-12-2019, 10:43 AM
Replies: 13,099
Views: 1,962,428
Posted By Kelseyrc

I don't know anything about the Reds motor. But...

I don't know anything about the Reds motor. But 30* of timing and gearing at 81/24 seems really low to me. What temp is your motor coming off the track at?

I run a Reedy S + 13.5 and my timing is...
01-24-2019, 03:08 PM
Replies: 6
Views: 580
Posted By Kelseyrc

Most everyone that I know solders directly to the...

Most everyone that I know solders directly to the can, but if you are planning on changing motors out frequently the ease of using bullet connectors would probably be worth it. There probably isn't...
01-24-2019, 02:36 PM
Replies: 7
Views: 595
Posted By Kelseyrc

I also use sticky kicks but use either the orange...

I also use sticky kicks but use either the orange or purple
01-22-2019, 08:44 AM
Replies: 2,879
Views: 479,001
Posted By Kelseyrc

That part # include both covers. 1 for the gull...

That part # include both covers. 1 for the gull and 1 for the flat.
01-18-2019, 09:35 PM
Replies: 24
Views: 2,209
Posted By Kelseyrc

You should download the hudy guide, here is the...

You should download the hudy guide, here is the link for it.

https://www.hudy.net/xhudy/products/proddwnld.php?prod_id=268&Hudy_Session=22ab36370fab55b04b98df22e24e50f8

It will give you a lot...
01-18-2019, 07:00 PM
Replies: 24
Views: 2,209
Posted By Kelseyrc

I think you are talking about toe and not camber....

I think you are talking about toe and not camber. You never should run positive camber only negative. However, toe out or positive toe will give you more initial steering but can cause the buggy to...
12-18-2018, 11:39 AM
Replies: 9,118
Views: 2,007,159
Posted By Kelseyrc

if you haven't done sosalready, I wotuld add the...

if you haven't done sosalready, I wotuld add the brass front bulkhead and steel servo and electronics plate.
12-17-2018, 02:33 PM
Replies: 2,879
Views: 479,001
Posted By Kelseyrc

Yes, those parts are interchangeable. Just...

Yes, those parts are interchangeable. Just remember that there are two versions of the front tower, one for flat arms and one for gullwing arms.
12-10-2018, 10:03 AM
Replies: 2,879
Views: 479,001
Posted By Kelseyrc

Ive broken the stock plastic bulkhead on small...

Ive broken the stock plastic bulkhead on small hits to the pipes. I usually run the aluminum bulkhead now on clay but now instead of the bulkhead breaking on these hits, the arms and hinge pins take...
12-05-2018, 03:27 PM
Replies: 32
Views: 3,887
Posted By Kelseyrc

I agree that the Maclan doesn't fall into the all...

I agree that the Maclan doesn't fall into the all variants sold category. However, it does seem to me that the section on aftermarket tuning would apply to the example. Given that, I would think that...
Showing results 1 to 25 of 176
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service