Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: azeroth
Showing results 1 to 25 of 500
Search took 0.57 seconds.
04-18-2019, 12:06 PM
Replies: 763
Views: 53,721
Posted By azeroth

ah yes the old days 12th scale nicads brushed...

ah yes the old days 12th scale nicads brushed motor a,b,c,d foam and brushed motors and had a gas 4cell indoors 6 cell outside 4minute mains and hand scoring
04-15-2019, 09:21 PM
Replies: 24
Views: 2,318
Posted By azeroth

i have been running the zx7 arms and knuckles on...

i have been running the zx7 arms and knuckles on my zx6 with exotek c hubs since the parts became available and have only broke one so far on on our indoor clay tracks here in the midwest and on crc...
02-21-2019, 08:27 AM
Replies: 47,640
Views: 4,927,055
Posted By azeroth

I haven't run 12th in quite awhile but have been...

I haven't run 12th in quite awhile but have been running the gen2 in every ecar I own stock and mod 2 and 4 wheel buggies and TC along with my 2 12th scalers. I know I was using a recommended...
02-19-2019, 10:17 AM
Replies: 2,399
Views: 564,847
Posted By azeroth

should be the same parts if your talking front...

should be the same parts if your talking front and rear if you are going to go to the center dii you will also need the drive shafts
Forum: Racing Forum
02-07-2019, 08:18 AM
Replies: 6
Views: 1,716
Posted By azeroth

actually its the 4th track that I know of in the...

actually its the 4th track that I know of in the last year
race-em rc Rockford indoor clay
team nitro's track in Lynnwood onroad asphalt
time warp any day now indoor clay
and yes it does SUCK ...
01-26-2019, 08:30 AM
Replies: 2,399
Views: 564,847
Posted By azeroth

I know the kit parts are the same between them I...

I know the kit parts are the same between them I also know the kyosho carbon parts are different than the kit and the new LD front tower is significantly different than the 6 version
01-10-2019, 08:28 AM
Replies: 178
Views: 31,923
Posted By azeroth

1 NO if a concern use the stock plastic arm (I...

1 NO if a concern use the stock plastic arm (I don't but I run a protek 160t servo with a TLR arm) usually you will wreck something else before killing the servo like a c hub knuckle or arm ball cup...
01-09-2019, 08:12 AM
Replies: 178
Views: 31,923
Posted By azeroth

I have broken a couple of arms no where near as...

I have broken a couple of arms no where near as many as the old flat arms but I have had a few shock shafts break and being the only thing broken at times
11-27-2018, 12:41 PM
Replies: 4
Views: 320
Posted By azeroth

1c = 5.5amps recommended charge rate 5 amps is...

1c = 5.5amps recommended charge rate
5 amps is fine 7.4 setting is fine I always balance charge but I rotate between multiple batteries
if it is a b6ac v2 it has a setting for hv but most tracks...
11-12-2018, 11:29 AM
Replies: 14,972
Views: 2,204,290
Posted By azeroth

yes using the rb7 front end already all the way...

yes using the rb7 front end already all the way in on arm on rear I think I am going shorten the shock ends both ends and maybe lighten up on the oils some more
11-12-2018, 09:11 AM
Replies: 14,972
Views: 2,204,290
Posted By azeroth

ok guys tell me whats wrong with this setup on...

ok guys tell me whats wrong with this setup on clay it is truly jeckyl and hyde from being on rails one day to completely undrivable the next rear gets so loose you can't drive it in a straight line...
09-21-2018, 08:48 AM
Replies: 178
Views: 31,923
Posted By azeroth

I have installed the rb7 arms knuckles and cf...

I have installed the rb7 arms knuckles and cf shock towers on my rb6 direct bolt on but you will need to swap out a ball cup on the top link and the tie rod assembled in a different combo between the...
09-07-2018, 10:10 AM
Replies: 2,399
Views: 564,847
Posted By azeroth

I like the changes most I have done. I have been...

I like the changes most I have done. I have been running gull wing arms on one of mine with AE hub carrier and knuckles and with gear difs and slipper is the only way to go would of like to seen...
08-29-2018, 09:18 AM
Replies: 178
Views: 31,923
Posted By azeroth

no the seating flange is a hex

no the seating flange is a hex
08-16-2018, 09:15 AM
Replies: 2,399
Views: 564,847
Posted By azeroth

older chassis than others and rumors of a updated...

older chassis than others and rumors of a updated version coming but it is a great car I have 2 alittle heavy but perform great
07-20-2018, 08:22 AM
Replies: 14,972
Views: 2,204,290
Posted By azeroth

my mid motor inline rb6 holds it own against all...

my mid motor inline rb6 holds it own against all comers at my local tracks so I don't think your 6.6 will have a issue
06-12-2018, 08:23 AM
Replies: 27
Views: 1,272
Posted By azeroth

this stuff is much better use it daily on job has...

this stuff is much better use it daily on job has body and don't slop all over https://www.wurthusa.com/search/?text=thread+locker
06-08-2018, 03:57 PM
Replies: 5,561
Views: 346,191
Posted By azeroth

the weekend of the 22-24 is the Midwest series...

the weekend of the 22-24 is the Midwest series round 2 (nitro On-road)
05-31-2018, 11:23 PM
Replies: 82
Views: 9,496
Posted By azeroth

Thanks Troy ... OOOH sooo funny Nick

Thanks Troy ... OOOH sooo funny Nick
05-31-2018, 08:56 AM
Replies: 82
Views: 9,496
Posted By azeroth

ok troy what tires are working in mod I had 3...

ok troy what tires are working in mod I had 3 tires let loose in three runs some only lasted 2-4 laps before coming apart but then I am thinking to just stick to my nitro cars.
05-24-2018, 05:15 PM
Replies: 82
Views: 9,496
Posted By azeroth

we will try and keep separate but we will combine...

we will try and keep separate but we will combine if necessary to fill the class so everybody runs Otto
Forum: Nitro On-Road
04-07-2018, 08:11 AM
Replies: 645
Views: 162,212
Posted By azeroth

yes you interpret it correctly Vibration Could be...

yes you interpret it correctly Vibration Could be a bad bearing but if the screws are hitting verify Tight and that it could be just adding a shim between bearing and "gearbox" yes that is what the...
04-06-2018, 12:09 PM
Replies: 5,561
Views: 346,191
Posted By azeroth

Well Rumors have it that it will May 6th Will be...

Well Rumors have it that it will May 6th Will be the first scheduled Prepped Track Sunday(by Team Nitro) unless there are some good weekends that don't step on another event. I personally am Looking...
Forum: Nitro On-Road
03-25-2018, 09:41 PM
Replies: 645
Views: 162,212
Posted By azeroth

i run the protek low profile servos and a protek...

i run the protek low profile servos and a protek lipo with a rex legend12r nova 2660 pipe med header balance was spot on no weights needed
03-22-2018, 08:29 AM
Replies: 2,399
Views: 564,847
Posted By azeroth

I am running 21/78 7k front 5k rear center...

I am running 21/78 7k front 5k rear center slipper trackstar track size 25/35
22/78 5k f 5k r center slipper trinity D4
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service