Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: trf211
Showing results 1 to 25 of 279
Search took 0.11 seconds.
Today, 11:29 AM
Replies: 6
Views: 303
Posted By trf211

Hmm alright. Are you noticing voltage drop off...

Hmm alright. Are you noticing voltage drop off later in the run or just comparing to see what other people use? The timing on the can and esc can quickly increase amp draw and drain the battery while...
Today, 10:18 AM
Replies: 463
Views: 78,182
Posted By trf211

Are both sides of the slipper spring perfectly...

Are both sides of the slipper spring perfectly flat? If the spring gets bent somehow and both sides are no longer perfectly parallel, the offset side will preload the slipper plate unevenly causing a...
Today, 08:53 AM
Replies: 6
Views: 303
Posted By trf211

Sounds a bit high to me to be honest. What is...

Sounds a bit high to me to be honest. What is your motor timing and esc timing?
07-13-2019, 06:04 PM
Replies: 4,204
Views: 932,071
Posted By trf211

Those do. The front exotek bones are slightly...

Those do. The front exotek bones are slightly heavier than the Alu MIP and are less prone to bending in a crash.
07-10-2019, 09:26 AM
Replies: 11
Views: 761
Posted By trf211

This may sound strange but I've found the ports...

This may sound strange but I've found the ports for the sensor wires on Hobbywing stuff can be deep. A wire can look and feel plugged in and not be fully connected. It's a good habit to double check...
06-27-2019, 10:18 AM
Replies: 969
Views: 149,497
Posted By trf211

We put 15k in the front diff, increased rear...

We put 15k in the front diff, increased rear toe(C pill double dot up and in, D pill double dot up and out)put the front a&b pills at center center and called it a day. Dropped .5 - 1 second off...
06-20-2019, 07:24 PM
Replies: 969
Views: 149,497
Posted By trf211

I'll test it but my times only went faster the...

I'll test it but my times only went faster the short I went. Currently sitting 1st in our series race at our track with it, should have a good setup sheet in a few more races for indoor clay tracks.
06-20-2019, 04:09 PM
Replies: 969
Views: 149,497
Posted By trf211

Interesting. I went the opposite route by...

Interesting. I went the opposite route by flipping the hubs and running the shortest link possible.
06-19-2019, 08:15 AM
Replies: 10
Views: 682
Posted By trf211

Most likely a Club Racer kit. Looks exactly the...

Most likely a Club Racer kit. Looks exactly the same anodizing as the b64 CR.
06-17-2019, 09:49 AM
Replies: 463
Views: 78,182
Posted By trf211

If you have a vertical surface on your receiver...

If you have a vertical surface on your receiver you can CA glue a piece of fuel tubing and use that to mount your antenna tube. Not the most 'factory' solution but I suppose it would work.
06-15-2019, 09:44 AM
Replies: 810
Views: 101,667
Posted By trf211

The dogbones are their most efficient and free...

The dogbones are their most efficient and free when they are flat and straight out from the diff. Anytime the dogbones are at an angle from the diff and you are on throttle the drive line will want...
06-11-2019, 10:06 AM
Replies: 5
Views: 834
Posted By trf211

Depends how competitive you and your class are....

Depends how competitive you and your class are. If you are still learning then it will be alright but if you have more time under your belt I would suggest something else. They need a bit of work to...
06-08-2019, 06:44 PM
Replies: 463
Views: 78,182
Posted By trf211

Haven't gotten a b74 yet to test that but on our...

Haven't gotten a b74 yet to test that but on our clay track we're still toe to toe in our mod class. With the b74 still in its infancy and the 64 plateauing, the b74 can only get faster.
06-06-2019, 05:32 PM
Replies: 463
Views: 78,182
Posted By trf211

Only the 31mm rear kashima 'tall' rear shock...

Only the 31mm rear kashima 'tall' rear shock bodies that are available for the b6.1/b64 will cross over to the 74.
06-03-2019, 07:10 PM
Replies: 4,204
Views: 932,071
Posted By trf211

Yeah occasionally you'll have to trim inner edges...

Yeah occasionally you'll have to trim inner edges of the tabs on a new steering knuckle for the freest rotation, before you even install the screws. It will squeeze against the caster block. Used...
06-03-2019, 01:51 PM
Replies: 4,204
Views: 932,071
Posted By trf211

Plastic piece I can't say but the axle height...

Plastic piece I can't say but the axle height bushings on the front changed during some point. Went from a darker blue anodizing to a lighter shade of blue and from what I can tell the newer lighter...
05-29-2019, 06:32 PM
Replies: 2,935
Views: 498,508
Posted By trf211

It's a known issue and they released a new batch...

It's a known issue and they released a new batch of them with a different part number.
05-28-2019, 08:05 PM
Replies: 16
Views: 1,766
Posted By trf211

Another voucher for the Yeah Racing 30mm aluminum...

Another voucher for the Yeah Racing 30mm aluminum fan. I've heard some people complain of the noise and wear them out on high voltage by soldering the wires directly to the battery posts, but in my...
05-26-2019, 04:09 PM
Replies: 463
Views: 78,182
Posted By trf211

I've heard the team guys are choosing between the...

I've heard the team guys are choosing between the 18 and 20mm horn.
05-25-2019, 08:50 PM
Replies: 4,204
Views: 932,071
Posted By trf211

Check to see if you misplaced some diff shims in...

Check to see if you misplaced some diff shims in the process of changing those parts, they can be a big source of drivetrain whine. 1 o-ring in the front outdrive and 2 in the rear outdrive of the...
05-25-2019, 09:34 AM
Replies: 260
Views: 18,493
Posted By trf211

B64 slipper fits in the eb410 with no...

B64 slipper fits in the eb410 with no modifications from what I understand.

posts 2515 in the eb410 thread.
05-24-2019, 11:57 AM
Replies: 2,935
Views: 498,508
Posted By trf211

21mm front, 28.5mm rear is the base setup and a...

21mm front, 28.5mm rear is the base setup and a pretty balanced starting point.
05-23-2019, 04:58 PM
Replies: 2,935
Views: 498,508
Posted By trf211

A few other at our track and I noticed the b6.1...

A few other at our track and I noticed the b6.1 from the box seemed to favor the back end upon landing. What I mean by that is when landing on all 4 wheels the front suspension will stop absorbing...
05-23-2019, 04:37 PM
Replies: 2,935
Views: 498,508
Posted By trf211

Richard adding a little more shock stroke will...

Richard adding a little more shock stroke will help. To me the only things that stick out on the setup sheet that will weaken the landing ability is the 27mm shock stroke, 28.5mm is a good starting...
05-23-2019, 10:54 AM
Replies: 2,935
Views: 498,508
Posted By trf211

Need more detailed info on your current setup...

Need more detailed info on your current setup before suggesting changes.
Showing results 1 to 25 of 279
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service