R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: sg1
Showing results 1 to 25 of 500
Search took 0.79 seconds.
05-20-2021, 10:26 AM
Replies: 2,569
Views: 449,429
Posted By sg1

34 to 38* on the motolyser works well with the...

34 to 38* on the motolyser works well with the 21.5 SMC..
how small of spur did you run? 68 or lower is a good size.
05-14-2021, 05:05 PM
Replies: 2,085
Views: 424,134
Posted By sg1

https://cimg1.ibsrv.net/gimg/www.rctech.net-vbulle...

https://cimg1.ibsrv.net/gimg/www.rctech.net-vbulletin/500x500/151017_500x500_d147665f70a19583dde0031780734ad8b170fed6.jpeg
I dont have a pic on my phone, but this is from the website. I removed the...
05-14-2021, 03:05 AM
Replies: 2,085
Views: 424,134
Posted By sg1

Boosred22d set up

I've been running the Roche WGTR since it came out. I removed all the bracing on it, went to 30k in the tubes, 10* reactive, 1* camber and had to adjust shims in the front for ground clearance. What...
02-19-2020, 02:24 PM
Replies: 2,569
Views: 449,429
Posted By sg1

The 12.5 4 line may be too strong for open...

The 12.5 4 line may be too strong for open timing. Maybe a weak 12.3 would be a better choice. In open classes most of the time starting around 16* on the motolyser is a good starting point.
01-16-2020, 08:23 AM
Replies: 2,569
Views: 449,429
Posted By sg1

when you say it gets hot going up 1 tooth.. Is it...

when you say it gets hot going up 1 tooth.. Is it 120* or more? Does the bottom end feel soft or fade during the race?

The full ceramic I have tested just gained in noise..lol.. I saw no...
01-16-2020, 03:04 AM
Replies: 2,569
Views: 449,429
Posted By sg1

There are some instances where a softer rotor...

There are some instances where a softer rotor works better in some of the older motors. The older stator didn't create the rpm as the v3 does and going to the softer rotor worked better. Just watch...
11-13-2019, 04:25 PM
Replies: 2,569
Views: 449,429
Posted By sg1

To be honest I have never looked at a max. RPM...

To be honest I have never looked at a max. RPM number..
The answer is not much help..lol..
I go by feel on the track, lap times, fade, and temp.. I don't look at a max. RPM
10-20-2019, 03:55 PM
Replies: 2,569
Views: 449,429
Posted By sg1

GREAT JOB!!

GREAT JOB!!
10-07-2019, 05:27 AM
Replies: 2,569
Views: 449,429
Posted By sg1

Not many run timing/boost in their esc's here.. ...

Not many run timing/boost in their esc's here..
The v3 is not a torque based design.
You can get smaller diameter and weaker rotors to run.
The few that have run it went 18* motor timing with a...
10-02-2019, 10:02 AM
Replies: 2,569
Views: 449,429
Posted By sg1

It would be best to give John a call or text...

It would be best to give John a call or text about pricing, that's his area :) 978-337-0429
As for the 6000 pack it is a 110C racing from the manufacture.
That pack is replacing the 4800 packs,...
10-01-2019, 10:16 AM
Replies: 2,569
Views: 449,429
Posted By sg1

Some ideas are being kicked around.. but nothing...

Some ideas are being kicked around.. but nothing is set in stone
John does have the aluminum cased fans :)
He also recommends the 6000 shorty for offroad buggy, He is doing some testing with some...
10-01-2019, 09:45 AM
Replies: 2,569
Views: 449,429
Posted By sg1

With medium traction on an average size track 48*...

With medium traction on an average size track 48* to start is good.
If you run a spool or ball diff go with a 98 to 100 spur and a 28 or 29 pinion to start.
If the traction is higher or the track...
09-30-2019, 03:34 PM
Replies: 2,569
Views: 449,429
Posted By sg1

Just a standard SS shield, if you want rubber...

Just a standard SS shield, if you want rubber shields they are a standard size (1/8 x 3/8)
09-25-2019, 05:36 AM
Replies: 2,569
Views: 449,429
Posted By sg1

USVTA Southern Nats Results

https://cimg9.ibsrv.net/gimg/www.rctech.net-vbulletin/960x540/71751561_2359276430867319_2666604469482946560_n_c64f8e92c29c68a73757d79adcb831180790e98a.jpg
I had great results at the USVTA Southern...
08-29-2019, 05:59 AM
Replies: 96
Views: 14,753
Posted By sg1

https://cimg0.ibsrv.net/gimg/www.rctech.net-vbulle...

https://cimg0.ibsrv.net/gimg/www.rctech.net-vbulletin/934x456/capture_3c07dfe109c05e58c3f3b2a2a157916ea0e39371.png
08-26-2019, 05:47 AM
Replies: 898
Views: 115,476
Posted By sg1

I just got some in and am prepping them now :)

I just got some in and am prepping them now :)
08-23-2019, 11:45 AM
Replies: 2,569
Views: 449,429
Posted By sg1

Motors ordered today will be shipped Monday. ...

Motors ordered today will be shipped Monday.
Buggy: If the infield is needed, 28-29/72.. if you need more straight try a 30-31/72
Truck: We went to 75 spur.. try that with a 22 to start.
08-05-2019, 05:35 AM
Replies: 2,569
Views: 449,429
Posted By sg1

https://cimg1.ibsrv.net/gimg/www.rctech.net-vbulle...

https://cimg1.ibsrv.net/gimg/www.rctech.net-vbulletin/651x783/nats_62dc843e290bc38b0b00f7a2892d19b055e5f0ef.png...
07-29-2019, 10:12 AM
Replies: 2,569
Views: 449,429
Posted By sg1

The motor doesn't have tons of RPM.. You will...

The motor doesn't have tons of RPM.. You will just be at tons of timing to gain the RPM so you will need a much different FDR
You total timing will be close to 62 to 64*
07-29-2019, 08:19 AM
Replies: 2,569
Views: 449,429
Posted By sg1

Try going up more on timing. Set it to 45* on can...

Try going up more on timing. Set it to 45* on can and a 26-78 to start.
Run a few minutes and check motor temps.
If you are running cool, 100* or so, and lacking rip and top end add 5* more timing,...
07-29-2019, 05:39 AM
Replies: 2,569
Views: 449,429
Posted By sg1

Only 35ft?

Only 35ft?
07-29-2019, 05:12 AM
Replies: 2,569
Views: 449,429
Posted By sg1

Sorry for the delay getting back to you! I just...

Sorry for the delay getting back to you!
I just got back from a 3 day race :)
What size track and surface are you running on?
07-25-2019, 05:16 AM
Replies: 2,569
Views: 449,429
Posted By sg1

Take it apart and see what's seized up. ...

Take it apart and see what's seized up.
Depending on how it was taken care of, I have seen the rotors start to seize in the bearing's ID
If that's what's going on that can be polished out.
If it's...
07-24-2019, 03:36 PM
Replies: 2,569
Views: 449,429
Posted By sg1

The can timing does not represent total timing on...

The can timing does not represent total timing on the V1. There is 18* or so on the sensor board that needs to be added to the can number in order to get total timing. In off Road with that motor...
07-24-2019, 02:40 PM
Replies: 2,569
Views: 449,429
Posted By sg1

There is a big jump in performance.. I would...

There is a big jump in performance..
I would still give it a try.
That version was a torque monster!
Try bumping the timing up on the can to 30* And see how it runs. What will you be running it in...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.