Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: bash bros
Showing results 1 to 25 of 500
Search took 0.26 seconds.
07-25-2019, 07:08 PM
Replies: 10,860
Views: 1,773,108
Posted By bash bros

I've never had any problems going back and forth...

I've never had any problems going back and forth between nova and o'donnell plugs, those are the only two types I use.

Try experimenting with plugs, between the 77t, 97t, c5tgc, or c6tgc I usually...
07-24-2019, 06:46 PM
Replies: 10,860
Views: 1,773,108
Posted By bash bros

Ever try swapping to a c5tgc instead? I've...

Ever try swapping to a c5tgc instead?

I've had certain Novas, like the Elite 5 and Elite 8 that just seem to run better on a c5tgc instead of a c6tgc for whatever reason. Seems to improve the idle...
11-16-2017, 07:12 PM
Replies: 8
Views: 1,143
Posted By bash bros

If you look around you can find the same bearings...

If you look around you can find the same bearings they sell at places like Avid for a buck a piece on ebay, straight from China for .30 or .40 cents a piece if you don't mind waiting 1-2 weeks for...
06-11-2017, 01:49 PM
Replies: 30
Views: 8,713
Posted By bash bros

M2C is the best. Their clutches and motor mounts...

M2C is the best. Their clutches and motor mounts make life easier :)
06-07-2017, 05:25 PM
Replies: 4
Views: 1,112
Posted By bash bros

Pretty much any decent 5000mah 3s or 4s lipo will...

Pretty much any decent 5000mah 3s or 4s lipo will work fine and go quite a while between charges. SMC has nice batteries for a decent price.
03-11-2017, 10:11 AM
Replies: 3,924
Views: 1,020,762
Posted By bash bros

I've used a couple sets and they're not bad for...

I've used a couple sets and they're not bad for 10 bucks. They were damn near identical to the Protek ones at Amain.
02-25-2017, 07:33 PM
Replies: 3,924
Views: 1,020,762
Posted By bash bros

Yeah they look like part# 2105 for the 7 ...

Yeah they look like part# 2105 for the 7

2105-b can fit also fit the 8x16 bearing on the inside
02-17-2017, 04:19 AM
Replies: 135
Views: 17,927
Posted By bash bros

I was at F, back to C currently. Probably F again...

I was at F, back to C currently. Probably F again if there were more tracks in my area though.
02-14-2017, 03:35 PM
Replies: 2
Views: 1,149
Posted By bash bros

You might be better off looking around the...

You might be better off looking around the Minneapolis area, theres not much for tracks near Eau Claire
01-12-2017, 07:07 PM
Replies: 593
Views: 94,055
Posted By bash bros

This. You would think the Mugen would fit...

This.

You would think the Mugen would fit his aggressive driving style perfectly.
12-16-2016, 05:33 AM
Replies: 13
Views: 4,456
Posted By bash bros

I use Lutz's 'poor mans torque wrench' idea that...

I use Lutz's 'poor mans torque wrench' idea that he had in one of his vids. Basically you just hold your flathead or hex driver with the very tips of your thumb and fingers and tighten them as much...
12-13-2016, 01:07 PM
Replies: 10,860
Views: 1,773,108
Posted By bash bros

Except for a few minor differences with the crank...

Except for a few minor differences with the crank and piston, yeah it's very similar to the p5xlt. Both are solid engines in buggy or truggy.
11-23-2016, 05:15 AM
Replies: 11,365
Views: 1,361,031
Posted By bash bros

Usually you bottom the needle out while holding...

Usually you bottom the needle out while holding the carb wide open, but it's 100% pointless to copy someone else's carb settings anyway. Even if you're running the same fuel, plug, pipe, venturi you...
11-21-2016, 11:50 AM
Replies: 3
Views: 455
Posted By bash bros

Usually 6-8" is pretty ideal for the pressure...

Usually 6-8" is pretty ideal for the pressure line so I doubt that's the problem. I'd check the tank itself, if it has a sintered brass filter theres a good chance it's clogged with old gummed up...
11-10-2016, 01:37 PM
Replies: 10,860
Views: 1,773,108
Posted By bash bros

Try running a larger venturi. 5.4mm really...

Try running a larger venturi. 5.4mm really restricts power and narrows your tuning window. Not only that, but a lot of drivers will just drive more agressively with a smaller carb insert which will...
10-31-2016, 09:10 AM
Replies: 5
Views: 1,148
Posted By bash bros

Yes it's safe and I'm also almost positive it's...

Yes it's safe and I'm also almost positive it's just repackaged mineral oil at 1000% markup like a lot of things in this hobby.
10-21-2016, 06:42 AM
Replies: 7
Views: 2,657
Posted By bash bros

+1 Other common mistakes are making too...

+1

Other common mistakes are making too large of an adjustment on the needles. When you get close to the sweet spot, sometimes a very small <1 hr adjustment is all that's needed. Usually the low...
09-10-2016, 03:25 PM
Replies: 10
Views: 7,139
Posted By bash bros

Oil designed for air filters is still better....

Oil designed for air filters is still better. Something like No-Toil has a solvent mixed in so you get full coverage and penetration into the foam. After it evaporates it leaves only a super tacky...
09-10-2016, 03:21 PM
Replies: 7
Views: 1,560
Posted By bash bros

If it won't budge you may have to heat it up or...

If it won't budge you may have to heat it up or try using something you can get more leverage with. Something wood or plastic that won't scratch up the sleeve if it slips.
09-08-2016, 01:14 PM
Replies: 10,860
Views: 1,773,108
Posted By bash bros

I know it can vary quite a bit from setup to...

I know it can vary quite a bit from setup to setup, but with a race tuned p5 my lsn was always leaned out quite a bit, if you're counting turns usually about 4.25 to 4.75 turns out. Just keep in mind...
09-08-2016, 08:53 AM
Replies: 18
Views: 1,706
Posted By bash bros

Dynamite red handle 1.5, 2.0, 2.5mm hex wrench...

Dynamite red handle 1.5, 2.0, 2.5mm hex wrench set is the best bang for the buck imo. The tips round off quicker than the MIPs but it's easy to grind them down like new every couple of months.
...
09-08-2016, 03:40 AM
Replies: 10,860
Views: 1,773,108
Posted By bash bros

TKO-CB-MR25414 is the rear bearing, pretty sure...

TKO-CB-MR25414 is the rear bearing, pretty sure they only make a standard 7x19x6 front however. Nova is the only company that makes the double front shield as far as I'm aware.
09-05-2016, 07:55 PM
Replies: 3,924
Views: 1,020,762
Posted By bash bros

I know, I was referring to the claim that there's...

I know, I was referring to the claim that there's not going to be a new car only new parts for the 7r. I know they were working on a new wing mount but other than that I'm curious what new or revised...
09-04-2016, 04:14 PM
Replies: 3,924
Views: 1,020,762
Posted By bash bros

What parts does the 7r really need though? Once...

What parts does the 7r really need though? Once you get the center unis you're pretty much set, and if you want to get spend crazy you can get the alum hubs and cf towers. Most people already run the...
09-04-2016, 04:40 AM
Replies: 18
Views: 1,715
Posted By bash bros

They are safer, life can take a little more abuse...

They are safer, life can take a little more abuse than a lipo and won't vent like a lipo will if punctured. However, lipos are pretty safe if you follow a few basic rules like always balance charging...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.