R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: Autocratic
Showing results 1 to 25 of 500
Search took 0.31 seconds.
09-23-2019, 07:06 PM
Replies: 131
Views: 20,056
Posted By Autocratic

Are there any setups posted or found yet for the...

Are there any setups posted or found yet for the amain guys?
10-07-2015, 07:10 PM
Replies: 2,823
Views: 579,373
Posted By Autocratic

Car is pretty solid out of the box. Avid carbon...

Car is pretty solid out of the box. Avid carbon inserts are nice for the rear. Give a little more rear traction. The optional carbon hub towers are a good tuning option as well. Car comes with the...
10-04-2015, 10:00 AM
Replies: 374
Views: 45,882
Posted By Autocratic

Jorn is running the SRX4 with the front shafts...

Jorn is running the SRX4 with the front shafts removed.
07-28-2015, 06:48 PM
Replies: 2,823
Views: 579,373
Posted By Autocratic

No throttle randomly. Throttle was still holding...

No throttle randomly. Throttle was still holding tension at center, but wouldn't respond. If you touched the throttle horn it would start working again.
07-27-2015, 06:43 PM
Replies: 2,823
Views: 579,373
Posted By Autocratic

Mick, so what did you do to fix the issue? I...

Mick, so what did you do to fix the issue?

I had a 2274 fail on me as well recently in this car in the throttle position and it was working perfect in the D812.
07-23-2015, 08:35 PM
Replies: 2,823
Views: 579,373
Posted By Autocratic

The outer hole on the Hudy horn is still shorter...

The outer hole on the Hudy horn is still shorter than the plastic stock horn.
06-29-2015, 07:47 PM
Replies: 2,823
Views: 579,373
Posted By Autocratic

double post.

double post.
06-29-2015, 07:47 PM
Replies: 2,823
Views: 579,373
Posted By Autocratic

I accidently filled my front and center diffs...

I accidently filled my front and center diffs during a big race with 50k instead of 5k. Grabbed the wrong oil off the wall in the shop. Rear was 5k.

Buggy drove amazing and was super consistent....
06-25-2015, 06:38 PM
Replies: 21,428
Views: 4,064,151
Posted By Autocratic

Just built mine up as well. All four pistons are...

Just built mine up as well. All four pistons are tight and don't spin. Guess it's just hit/miss.
06-19-2015, 08:34 PM
Replies: 1,401
Views: 246,339
Posted By Autocratic

Do you still have the break-in shim installed?

Do you still have the break-in shim installed?
06-14-2015, 09:48 AM
Replies: 1,401
Views: 246,339
Posted By Autocratic

Well I figured out what my tuning issues were. ...

Well I figured out what my tuning issues were.

After taking apart the motor I found the case was cracked at the mounting tab, lengthwise. Small air leak causing it to run hot and stall out.
...
06-13-2015, 06:29 PM
Replies: 1,401
Views: 246,339
Posted By Autocratic

What are the factory carb settings? Having a hard...

What are the factory carb settings? Having a hard time getting a good tune on this motor and want to start over needle wise.
06-05-2015, 07:54 PM
Replies: 2,823
Views: 579,373
Posted By Autocratic

Two left in stock.

Two left in stock.
05-03-2015, 07:48 PM
Replies: 2,823
Views: 579,373
Posted By Autocratic

So far this car can only be had overseas correct?

So far this car can only be had overseas correct?
04-09-2015, 12:21 PM
Replies: 4
Views: 484
Posted By Autocratic

Bump

Bump
04-08-2015, 10:43 AM
Replies: 4
Views: 484
Posted By Autocratic

Bump

Bump
04-07-2015, 09:17 AM
Replies: 4
Views: 484
Posted By Autocratic

Bump

Bump
04-06-2015, 11:45 AM
03-21-2015, 01:02 PM
Replies: 146
Views: 22,894
Posted By Autocratic

High traction doesn't really mean more broken...

High traction doesn't really mean more broken parts but you're putting down the power better and you're driving faster. The same crash outdoor probably wouldn't see the same result indoor.
03-21-2015, 12:17 PM
Replies: 146
Views: 22,894
Posted By Autocratic

You're not going to break the rear inner hinge...

You're not going to break the rear inner hinge pins; steel or titanium. The steel pins are made from tool steel and are very strong. If you're bending the steel ones you're doing something wrong.
Forum: Texas Racing
03-20-2015, 10:46 AM
Replies: 11
Views: 2,176
Posted By Autocratic

Makes sense. Will be looking forward to this race.

Makes sense. Will be looking forward to this race.
Forum: Texas Racing
03-19-2015, 03:35 PM
Replies: 11
Views: 2,176
Posted By Autocratic

So what's the purpose of the teams?

So what's the purpose of the teams?
Forum: Texas Racing
03-19-2015, 07:50 AM
Replies: 11
Views: 2,176
Posted By Autocratic

Explain the team thing please.

Explain the team thing please.
03-17-2015, 11:57 AM
Replies: 71
Views: 15,662
Posted By Autocratic

Drew was running an RB6. Pretty sure Ty was the...

Drew was running an RB6. Pretty sure Ty was the only one running the car that will end up being the HB 2wd.
03-08-2015, 10:54 AM
Replies: 18
Views: 1,248
Posted By Autocratic

bump

bump
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.