R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: COBRARACING
Showing results 1 to 25 of 500
Search took 0.58 seconds.
10-26-2018, 01:10 AM
Replies: 468
Views: 154,349
Posted By COBRARACING

No fan required for 17.5T but the cooler the esc...

No fan required for 17.5T but the cooler the esc runs the more efficient it will be .
08-14-2018, 06:19 PM
Replies: 13,294
Views: 1,366,381
Posted By COBRARACING

set all you radio end points, set your neutral...

set all you radio end points, set your neutral range on the esc at 6% save it then re calibrate radio to esc .
08-10-2018, 12:43 AM
Replies: 468
Views: 154,349
Posted By COBRARACING

Hitec deal with Imax for their chargers not Skyrc...

Hitec deal with Imax for their chargers not Skyrc and the Toro is not a Hobbywing at all i assure you .Skyrc make all that G force stuff and yes they are very well known to copy others products fact...
08-09-2018, 08:38 PM
Replies: 468
Views: 154,349
Posted By COBRARACING

Skyrc only builds clones dont compare the Xr10...

Skyrc only builds clones dont compare the Xr10 pro 160 amp to the Toro no comparison whatsoever and thats the honest truth .The Hobbywing is state of the art technology from hardware to software no...
08-09-2018, 02:22 PM
Replies: 468
Views: 154,349
Posted By COBRARACING

No sorry just the programming 3 pin port also the...

No sorry just the programming 3 pin port also the fan port and no plan to use a usb port feature for programming.
05-19-2018, 07:00 PM
Replies: 468
Views: 154,349
Posted By COBRARACING

Change sensor cable , reload software from usb...

Change sensor cable , reload software from usb link and re-calibrate radio to esc and all will go back to normal.
05-13-2018, 02:47 PM
Replies: 468
Views: 154,349
Posted By COBRARACING

Anyone having issues with the new usb link please...

Anyone having issues with the new usb link please email me at [email protected] .

I will be able to send you a copy of the firmware.

please note: No gmail.com email address as they dont except...
05-13-2018, 02:46 PM
Replies: 539
Views: 93,252
Posted By COBRARACING

Anyone having issues with the new usb link please...

Anyone having issues with the new usb link please email me at [email protected] .

I will be able to send you a copy of the firmware.

please note: No gmail.com email address as they dont except...
05-13-2018, 02:45 PM
Replies: 12,554
Views: 1,703,469
Posted By COBRARACING

Anyone having issues with the new usb link please...

Anyone having issues with the new usb link please email me at [email protected] .

I will be able to send you a copy of the firmware.

please note: No gmail.com email address as they dont except...
05-13-2018, 02:40 PM
Replies: 690
Views: 257,946
Posted By COBRARACING

Yes 100% power board failure .Send it in for...

Yes 100% power board failure .Send it in for repair is your best bet.
05-13-2018, 04:39 AM
Replies: 690
Views: 257,946
Posted By COBRARACING

Did you change the sensor cable ? If not...

Did you change the sensor cable ?
If not please do so that will fix your issue but if you have changed it and the problem still exists then you have a mosfet power board issue fault.
04-08-2018, 07:16 AM
Replies: 539
Views: 93,252
Posted By COBRARACING

long Flashes is fine thats throttle if it flases...

long Flashes is fine thats throttle if it flases 2 times per second that is overheat so dont stress the escis function correctly.
03-29-2018, 08:25 PM
Replies: 13,294
Views: 1,366,381
Posted By COBRARACING

Yes check the motor sensor board pull it apart...

Yes check the motor sensor board pull it apart and have a look at the hall sensors they might be dirty
03-29-2018, 07:52 PM
Replies: 13,294
Views: 1,366,381
Posted By COBRARACING

Motor sensor board you need a hall sensor tester...

Motor sensor board you need a hall sensor tester as for the bec use a multimeter set to dc v and use the test point of the 3 pin program port - + should read 5.5v and above
03-29-2018, 07:46 PM
Replies: 13,294
Views: 1,366,381
Posted By COBRARACING

Either motor sensor board issue,Servo drawing to...

Either motor sensor board issue,Servo drawing to much current or bec failure in esc.
03-13-2018, 06:57 PM
Replies: 709
Views: 49,523
Posted By COBRARACING

Good luck with it all you are going to need it...

Good luck with it all you are going to need it because the fall out is going to be huge if it doesn't turn out i hope you have done your home work correctly especially with motor setups because...
03-13-2018, 06:41 PM
Replies: 709
Views: 49,523
Posted By COBRARACING

Entry level 25.5T Fixed for beginners is the Go.

Entry level 25.5T Fixed for beginners is the Go.
03-13-2018, 06:24 PM
Replies: 709
Views: 49,523
Posted By COBRARACING

A control motor will not fix stock racing because...

A control motor will not fix stock racing because the racer who came first last year will come first this year as simple as that because his or hers success is in their driving ability and chassis...
03-13-2018, 06:19 PM
12-18-2017, 07:04 PM
Replies: 13,294
Views: 1,366,381
Posted By COBRARACING

Re-Calibrate Esc to radio and it will go back to...

Re-Calibrate Esc to radio and it will go back to normal.
12-05-2017, 02:41 PM
Replies: 13,294
Views: 1,366,381
Posted By COBRARACING

So flashing red your in neutral then press button...

So flashing red your in neutral then press button once then full throttle press button again then reverse should work fine after that.
12-05-2017, 02:27 PM
Replies: 13,294
Views: 1,366,381
Posted By COBRARACING

Yes it is a calibration issue but you are doing...

Yes it is a calibration issue but you are doing one thing wrong very simple but we all have done it before.You need to enter calibration mode in one go and that mean powering up the esc and...
12-03-2017, 11:02 PM
Replies: 734
Views: 184,465
Posted By COBRARACING

Damaged Mosfet Basically Shorted but it will run...

Damaged Mosfet Basically Shorted but it will run like that by plugging in the battery and powering up without the Button.
If you dont mind powering it up like that it will work just fine.
11-24-2017, 02:20 PM
Replies: 13,294
Views: 1,366,381
Posted By COBRARACING

No it doesnt and never has.

No it doesnt and never has.
11-24-2017, 03:12 AM
Replies: 13,294
Views: 1,366,381
Posted By COBRARACING

4274 for 1/8th Truggy and 1/8th On Road 4268...

4274 for 1/8th Truggy and 1/8th On Road
4268 for Buggy or 1/8th Sct
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.