Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: JWATT
Showing results 1 to 25 of 280
Search took 0.06 seconds.
03-17-2008, 08:12 AM
Replies: 959
Views: 74,583
Posted By JWATT

Where might I find the results? Thanks

Where might I find the results?

Thanks
09-27-2007, 12:21 PM
07-20-2007, 07:52 AM
Replies: 6
Views: 536
Posted By JWATT

Probably can find it cheaper, but the minumum...

Probably can find it cheaper, but the minumum quantity will be 250-500' reel. Hard to justify.
03-20-2007, 09:33 AM
Replies: 785
Views: 61,599
Posted By JWATT

Our local Health Department almost shutdown the...

Our local Health Department almost shutdown the "Chili Bowl" race (indoors, midget sprints) when the spectators complained about the smoke/fumes from the engines. The organizer responded by getting...
02-28-2007, 01:22 PM
Replies: 11
Views: 1,048
Posted By JWATT

Measure the voltage in each cell individually...

Measure the voltage in each cell individually after the pack has peaked. See if all are close as far as voltage. You may have a bad cell.
01-08-2007, 01:23 PM
Replies: 453
Views: 52,399
Posted By JWATT

Where can I see the results?

Where can I see the results?
09-20-2006, 03:59 PM
Replies: 1,145
Views: 115,113
Posted By JWATT

NOPE!

NOPE!
09-19-2006, 02:32 PM
Replies: 1,145
Views: 115,113
Posted By JWATT

When does the "Live" site get going?

When does the "Live" site get going?
04-18-2006, 03:48 PM
Replies: 6
Views: 802
Posted By JWATT

Try putting in a new locking nut on the diff...

Try putting in a new locking nut on the diff bolt. Might want to use locktite too.
04-11-2006, 03:41 PM
Replies: 9
Views: 923
Posted By JWATT

Buy with confidence, good guy. Known him for 15...

Buy with confidence, good guy. Known him for 15 years.
04-10-2006, 09:34 AM
Replies: 13,258
Views: 1,573,130
Posted By JWATT

DUH! My bad, you guys are right! :eek:

DUH! My bad, you guys are right! :eek:
04-10-2006, 09:20 AM
Replies: 13,258
Views: 1,573,130
Posted By JWATT

Yes, you are right the motor spins the same...

Yes, you are right the motor spins the same direction, but by being on the other side of the spur, the SPUR'S direction is reversed. :nod:
03-24-2006, 02:59 PM
Replies: 13,258
Views: 1,573,130
Posted By JWATT

If the pinion is moved to the other side of the...

If the pinion is moved to the other side of the spur, it will reverse the spur's direction is the point I was trying to make. By moving the motor from one side of the car to another, it will...
03-24-2006, 02:39 PM
Replies: 13,258
Views: 1,573,130
Posted By JWATT

Wink Sooooo, I'm not getting beat cause my batts don't...

Sooooo, I'm not getting beat cause my batts don't have sky high numbers?!
03-24-2006, 02:27 PM
Replies: 13,258
Views: 1,573,130
Posted By JWATT

[QUOTE=andsetinn]If you'd move the motor in TC4...

[QUOTE=andsetinn]If you'd move the motor in TC4 to the other side without changing anything else the motor would be spinning in the same direction.

Yes, but the pinion would be on the other side...
03-24-2006, 08:18 AM
Replies: 5,873
Views: 505,651
Posted By JWATT

Listen while running laps. Or start from a dead...

Listen while running laps. Or start from a dead stop before the turn to get on the straight. Just want to be sure that the rpm at the beginning of the straight is similar to race conditions. If you...
03-24-2006, 07:50 AM
Replies: 5,873
Views: 505,651
Posted By JWATT

Your motor should reach peak rpm, just before the...

Your motor should reach peak rpm, just before the end of the longest straightaway. To get a good start point, ask some other racers at the track.
03-24-2006, 06:58 AM
Replies: 13
Views: 2,550
Posted By JWATT

To "run it in", I just take an old dog bone,...

To "run it in", I just take an old dog bone, chuck it up in a drill or Dremel, insert it into the diff (while it is out of the tranny), hold the other side of the diff with a screwdriver, and spin it...
03-17-2006, 12:58 PM
Replies: 0
Views: 1,920
Posted By JWATT

RC Boat

Anyone have a Pro Boat Gas Shockwave SuperSport 55 RTR for sale? Model #PRB2650.
03-08-2006, 03:50 PM
Replies: 15,877
Views: 2,031,185
Posted By JWATT

Take the shaft out and check the front and back...

Take the shaft out and check the front and back wheels. It might give you a place to start. If one is tighter than the other, then shimming the diff will probably be the trick, assuming the wheel...
03-01-2006, 03:28 PM
Replies: 12,235
Views: 1,056,720
Posted By JWATT

Sounds like you need new o-rings. Be sure the...

Sounds like you need new o-rings. Be sure the shock shaft is straight by
rolling it on a flat surface.
02-14-2006, 06:44 AM
Replies: 12,235
Views: 1,056,720
Posted By JWATT

Metric will not fit.

Metric will not fit.
02-13-2006, 07:35 AM
Replies: 12,235
Views: 1,056,720
Posted By JWATT

Buy 5-40 Screws.

Buy 5-40 Screws.
02-08-2006, 08:22 AM
Replies: 3,818
Views: 116,719
Posted By JWATT

Good Luck to both of you guys! :nod:

Good Luck to both of you guys! :nod:
02-01-2006, 02:47 PM
Replies: 12,235
Views: 1,056,720
Posted By JWATT

You need the special metric bearings for the one...

You need the special metric bearings for the one way (standard diff bearings ID is too small). My mistake, the diff housings are the same, it is the outdrives that are different between the nitro and...
Showing results 1 to 25 of 280
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.