R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: the daddy
Showing results 1 to 25 of 120
Search took 0.07 seconds.
03-20-2014, 02:09 PM
Replies: 2,460
Views: 382,108
Posted By the daddy

Thanks

Thanks
03-20-2014, 12:14 PM
Replies: 2,460
Views: 382,108
Posted By the daddy

Hello does anyone know what servo to run when the...

Hello does anyone know what servo to run when the car has the motor in the mid position and a standard size lipo stick pack.
12-23-2013, 06:18 AM
Replies: 3,056
Views: 302,983
Posted By the daddy

Carpet

Does this stuff work on carpet.
02-19-2013, 11:28 AM
Replies: 42
Views: 5,272
Posted By the daddy

I asked a friend of mine the same question once...

I asked a friend of mine the same question once he told me to think of a women's breasts but I could not pass this information on to my 10 year old son who I pit for so maybe you guys can tell me how...
01-22-2013, 12:42 PM
Replies: 124
Views: 39,723
Posted By the daddy

Isn't cast pouring into a mould with the...

Isn't cast pouring into a mould with the potential of air pockets and Cnc milled out of a cold block using a Cnc router
01-22-2013, 10:52 AM
Replies: 9
Views: 2,451
Posted By the daddy

very good servos for throttle and steering

very good servos for throttle and steering
01-19-2013, 02:50 AM
Replies: 10,669
Views: 1,643,968
Posted By the daddy

Do it your way heat cycle it much better than...

Do it your way heat cycle it much better than just forcing the piston through the liner
01-17-2013, 01:26 PM
Replies: 160
Views: 32,610
Posted By the daddy

Ok but is a plastic gear any good for racing

Ok but is a plastic gear any good for racing
01-16-2013, 11:17 AM
Replies: 160
Views: 32,610
Posted By the daddy

Metal spur

How much noise do these things make sounds like a bag of nails I have small bit of back lash from the pinion
01-07-2013, 09:29 AM
Replies: 10,238
Views: 1,406,265
Posted By the daddy

It's not an e buggy it's a conversion so no body...

It's not an e buggy it's a conversion so no body and no spur
01-07-2013, 06:15 AM
Replies: 10,238
Views: 1,406,265
Posted By the daddy

Will 4000 kv be too much seems everyone else is...

Will 4000 kv be too much seems everyone else is running between 1900 and 3000 kv I am going to use 4 cells
01-04-2013, 12:02 PM
Replies: 12
Views: 2,277
Posted By the daddy

Seen an mbx5 t rear shock tower break clean in...

Seen an mbx5 t rear shock tower break clean in half AL and that was won tuff mofo
01-03-2013, 09:34 AM
Replies: 10,238
Views: 1,406,265
Posted By the daddy

Pinion

Anyone know where to start with pinions for agama standard gearing 4000 kv motor
12-31-2012, 02:40 PM
Replies: 10,238
Views: 1,406,265
Posted By the daddy

Thanks but it's the agama conversion I'm thinking...

Thanks but it's the agama conversion I'm thinking of
12-31-2012, 04:23 AM
Replies: 10,238
Views: 1,406,265
Posted By the daddy

R2 chassis

Anyone know if the e conversion kit will fit the r2 chassis thanks
10-15-2012, 09:32 AM
Replies: 5
Views: 2,205
Posted By the daddy

B01 is a 5 port b02 is a 3 port

B01 is a 5 port b02 is a 3 port
06-25-2012, 12:32 PM
Replies: 8
Views: 2,242
Posted By the daddy

Try Schumacher mini pins dremel the first two to...

Try Schumacher mini pins dremel the first two to three pins of either edge
Of the front tires that should eliminate the grip roll but still give you good forward grip
06-06-2012, 02:11 PM
Replies: 20
Views: 1,623
Posted By the daddy

Will do

Will do
06-06-2012, 01:22 PM
Replies: 20
Views: 1,623
Posted By the daddy

There is a lot to be taken in at the weekend I...

There is a lot to be taken in at the weekend I ran a low bite clutch on a high bite track at first it seemed like a rich setting but after retuning I had the same simptons but with higher temps
06-06-2012, 12:23 PM
Replies: 20
Views: 1,623
Posted By the daddy

Thanks that puts my mind at rest exact answer I...

Thanks that puts my mind at rest exact answer I was looking for just wern't sure if I was cooking or wearing my engine out
06-06-2012, 12:10 PM
Replies: 20
Views: 1,623
Posted By the daddy

I know fair point but when running in minus 8c to...

I know fair point but when running in minus 8c to running 33c should your temps be the same
06-06-2012, 11:56 AM
Replies: 28
Views: 2,709
Posted By the daddy

Practice

Practice each section of the track individualy over and over then finally Thread it together And on race day try and put two solid qualifiers in and on the third balls out you never know you might...
06-06-2012, 11:36 AM
Replies: 20
Views: 1,623
Posted By the daddy

Engine temps

Getting a bit obsessed where the best place to take temp and a rough range is 225 to 270 would thisbe in any climate coz I know you boyz in oz and usa see high temps all the time in England were not...
06-05-2012, 09:21 AM
Replies: 879
Views: 82,826
Posted By the daddy

Grip

What springs for a hi bite track
05-24-2012, 09:01 AM
Replies: 3
Views: 357
Posted By the daddy

Thanks so I suppose it's just to take edge of it...

Thanks so I suppose it's just to take edge of it being fully charged
Showing results 1 to 25 of 120
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.