Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: RussF
Showing results 1 to 25 of 500
Search took 0.13 seconds.
09-14-2020, 01:41 PM
Replies: 6,963
Views: 923,151
Posted By RussF

Oh snap I just realized you are running the...

Oh snap I just realized you are running the McLaren P1 body. The front tires will contact the back side of the wheel well there. It needs to be dremeled out there.
09-14-2020, 01:38 PM
Replies: 6,963
Views: 923,151
Posted By RussF

Well really neither should be very tight but its...

Well really neither should be very tight but its usually with the ready set kits with no mods that the left or drivers side of the chassis wheel nut is over tightened. That pulls the axle through and...
09-14-2020, 11:14 AM
Replies: 6,963
Views: 923,151
Posted By RussF

In my experience its usually the wheel nut on the...

In my experience its usually the wheel nut on the left (opposite gear side) that is too tight. Don't over tighten that wheel nut with any diff, especially the stock gear diff. I usually snug it down...
08-24-2020, 01:01 PM
Replies: 6,963
Views: 923,151
Posted By RussF

PN makes a ball bearing motor can with Neo...

PN makes a ball bearing motor can with Neo magnets (http://www.kenonhobby.com/PN-Racing-130-Ball-Bearing-Motor-Case-Neo-Magnet_p_42225.html). Out of stock currently though. It wouldn't be legal in...
08-24-2020, 10:26 AM
Replies: 35
Views: 3,826
Posted By RussF

My experience this summer with Bittydesign bodies...

My experience this summer with Bittydesign bodies on T4-17 running on asphalt prepped parking lot medium+ grip track. Hyper has the most down force and is very stable, I mounted mine at 0mm. M410...
03-03-2020, 10:44 AM
Replies: 6,963
Views: 923,151
Posted By RussF

Not only that but 16/52 would put me down to 3.25...

Not only that but 16/52 would put me down to 3.25 FDR. I'm guessing an EVO board would be good down that low but I'd hate to find out the hard way. 18/52 goes sub 3 to 2.89. That seems crazy. Maybe...
02-28-2020, 03:27 PM
Replies: 6,963
Views: 923,151
Posted By RussF

Thanks Bill, I looked there and did not see the...

Thanks Bill, I looked there and did not see the 15 and 16 tooth procut 64p on the first check. I would really like to try a 16-17-18 and see how it works. Anybody know where to get 17-18?
02-28-2020, 02:21 PM
Replies: 6,963
Views: 923,151
Posted By RussF

Where does one typically get a 16-17 tooth 64p...

Where does one typically get a 16-17 tooth 64p pinion? That would be worth checking out.
02-19-2020, 10:08 AM
Replies: 6,963
Views: 923,151
Posted By RussF

Why was my brushless motor so slow on the top...

Why was my brushless motor so slow on the top end? This last weekend at the Ice Melter (https://www.facebook.com/WyomingMiniZ/) race I ran my PN2.5W equipped with EVO board and GL Racing 3500kv motor...
01-17-2020, 01:10 PM
Replies: 6,963
Views: 923,151
Posted By RussF

Did you measure it with a camber gauge? Can you...

Did you measure it with a camber gauge? Can you post a picture of it? This is an easier to understand how the pins work graphic.

https://i.postimg.cc/L6K2Fwp9/PN-AA-Arm-Camber-Adjustment.jpg...
01-14-2020, 09:00 AM
Replies: 6,963
Views: 923,151
Posted By RussF

So as I mentioned in the above post, now that I...

So as I mentioned in the above post, now that I have the EVO board installed I'm not sure how to make it work right. I have an EX-6 and have bound the receiver successfully. I soldered the motor...
01-14-2020, 08:50 AM
Replies: 6,963
Views: 923,151
Posted By RussF

I just finished installing an EVO board on my...

I just finished installing an EVO board on my PN2.5 chassis. It was pretty easy but required a few modifications to fit flat. I had to shave the protrusion off the servo motor holder and just a...
01-13-2020, 08:49 AM
Replies: 497
Views: 78,791
Posted By RussF

Salt Lake Mini-Z has them in stock SLMZ, 1/28th...

Salt Lake Mini-Z has them in stock SLMZ, 1/28th Racing Products (http://www.slmini-zstore.com/)
01-09-2020, 09:05 AM
Replies: 29
Views: 2,733
Posted By RussF

Nice, thanks. Where did you get it? cant see them...

Nice, thanks. Where did you get it? cant see them at Hobbyking.
01-08-2020, 10:30 AM
Replies: 29
Views: 2,733
Posted By RussF

What model (part number please) receiver did you...

What model (part number please) receiver did you use for the EVO?
11-07-2019, 02:49 PM
Replies: 2,770
Views: 533,177
Posted By RussF

I dont recall any slop with the chrome pivot...

I dont recall any slop with the chrome pivot balls. I now use the bronze ones but not real happy with those either as the coating peals off. However with either ball I can tighten the clamp screw...
10-29-2019, 04:06 PM
Replies: 497
Views: 78,791
Posted By RussF

Right rear would be the gear side. There should...

Right rear would be the gear side. There should be a slight side to side movement of the diff when installed as per instructions. If you mean the wheel can move side to side with the wheel nut on I...
08-12-2019, 02:50 PM
Replies: 827
Views: 206,907
Posted By RussF

I was doing some testing during and after racing...

I was doing some testing during and after racing this weekend. We have a smaller asphalt track guessing about 75x40 treated medium + grip...
07-30-2019, 03:03 PM
Replies: 827
Views: 206,907
Posted By RussF

Or at least not the back wheels maybe. But they...

Or at least not the back wheels maybe. But they sure make a nicer cut than I do. I ended up just lengthening the rear opening. Looks dumb, but it should work ok. I'm kinda out of room to open it too...
07-30-2019, 12:42 PM
Replies: 827
Views: 206,907
Posted By RussF

Ya because of the different set ups and such no...

Ya because of the different set ups and such no precut will be perfect. The first one I got (M410) worked so well and required minimal modification I thought I'd go for the JP8 in a pre-cut. The $4...
07-30-2019, 10:01 AM
Replies: 827
Views: 206,907
Posted By RussF

Question about the JP8 Pre-Cut for X-Ray T4...

Question about the JP8 Pre-Cut for X-Ray T4 17/18. I bought one and mounted it up. Its a little forward on the front wheels as expected but its way forward on the rear and not even close. I can swap...
04-09-2019, 09:48 PM
Replies: 497
Views: 78,791
Posted By RussF

Still not working no matter what I do. The...

Still not working no matter what I do. The problem seems to be after getting it into calibration mode it wont do anything more. When i push the program button to set nuetral It will either shut off...
04-09-2019, 03:26 PM
Replies: 497
Views: 78,791
Posted By RussF

Will do. I was thinking the same thing since at...

Will do. I was thinking the same thing since at the time of binding only the servo was plugged in. Thanks.
04-09-2019, 11:17 AM
Replies: 497
Views: 78,791
Posted By RussF

Yes this is the procedure I did the most as it...

Yes this is the procedure I did the most as it should have worked. Tried holding longer after trying it and failing. I never got the green light blinking. I've tried it a little slow and faster, same...
04-09-2019, 09:34 AM
Replies: 497
Views: 78,791
Posted By RussF

So I got my ASF receiver yesterday and got it...

So I got my ASF receiver yesterday and got it bound up to my EX-6 just fine. The GX-011 ASF-H receiver doesn't say which port is steering or ESC so I guessed the one closest to the bind button was...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.