R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
 
Page 1 of 13
1
2
3
11
Last »
Search: Posts Made By: Baja-Boy
Showing results 1 to 25 of 303
Search took 0.02 seconds.
Forum: Radio and Electronics
10-01-2019, 01:55 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

it all depends what is causing the issue....

it all depends what is causing the issue. Typically the easiest way to be sure is to send in via an RMA at HADRMA.com our turn around is usually pretty quick
Forum: Radio and Electronics
09-28-2019, 08:19 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

I’m your primary Maclan tech,...

I’m your primary Maclan tech, [email protected]

nikos is still on the team but is very very busy with his Horizon job. Any inquiry I am glad to take:)
Forum: Radio and Electronics
07-29-2019, 09:13 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

I have never had a single bec issue or complaint...

I have never had a single bec issue or complaint (I am USA tech support for Maclan Racing)

Also for the red light no throttle issue, have you contacted tech support? my email is...
Forum: Radio and Electronics
04-15-2019, 01:34 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

I am “some guy named Ian” and I’ve put in a lot...

I am “some guy named Ian” and I’ve put in a lot of calls for our company. Whenever we have a customer put in a request, that request stays live until a customer is taken care of. Could you please...
Forum: Radio and Electronics
01-05-2019, 08:09 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

We are super excited to have a driver like Jared...

We are super excited to have a driver like Jared Tebo

We are working very very very hard to bring the 1/8 esc online, many iterations and samples to make sure it is as good as our 1/10 escs. I...
Forum: Radio and Electronics
07-22-2018, 10:01 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

That video brings up a lot of questions. I think...

That video brings up a lot of questions. I think the very first is, is the esc even applying full brake (I can’t see the status led to see if the orange went solid). His channel is an interesting mix...
Forum: Radio and Electronics
07-09-2018, 09:04 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

There are no issues with the pico, it is still...

There are no issues with the pico, it is still the same design. Very few have had any problems (people only tend to post on a forum when they have an issue). It is a great choice for stock racing...
Forum: Radio and Electronics
07-09-2018, 08:55 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

<blockquote><cite>zx12r785;15256115</cite><div>On...

<blockquote><cite>zx12r785;15256115</cite><div>On a different note...can the Pico be plugged into the prolink with the USB cords to change settings? Hate using the reciver cord to change settings...
Forum: Radio and Electronics
06-30-2018, 08:41 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

130-150° range depending on ambient. That’s with...

130-150° range depending on ambient. That’s with one of the HV 30mm fans
Forum: Radio and Electronics
06-28-2018, 05:21 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

I run between 29-32/75 on carpet, and 29-35/72 on...

I run between 29-32/75 on carpet, and 29-35/72 on dirt/clay. that’s in a yz2/b6/xb2 etc. I am unsure of FDR. Def want more timing than not. The 6 amp setting is not the best for these motors. worry...
Forum: Radio and Electronics
06-28-2018, 05:19 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

The only guarantee one is the long from collar,...

The only guarantee one is the long from collar, there can be some small ones behind that.
Forum: Radio and Electronics
06-27-2018, 04:21 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

when it shows silly things like that the firmware...

when it shows silly things like that the firmware is corrupt and a reflash will fix it. Only happens rarely and usually during calibration. The voltage etc it shows is not correct, the bec will still...
Forum: Radio and Electronics
06-24-2018, 08:17 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

do you have access to any kind of motor analyzer?...

do you have access to any kind of motor analyzer? You’d be amazed how much internal timing can change from the end bell.

one of mine is right on, the other is 4 degrees off (it reads lower than it...
Forum: Radio and Electronics
06-21-2018, 02:40 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

same settings as the black rotor (at least that’s...

same settings as the black rotor (at least that’s what I run)
Forum: Radio and Electronics
05-28-2018, 06:59 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

i set the timing at 50 on the can to start with...

i set the timing at 50 on the can to start with the v2. Also gear it lower than the v1. It’s sounds very counter intuitive but the motor then runs with a very “cleared out” feel.

what chassis is...
Forum: Radio and Electronics
04-25-2018, 06:43 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

any solder bridge will cause damage to the ESC,...

any solder bridge will cause damage to the ESC, make sure there is no solder where there shouldn’t be.
Forum: Radio and Electronics
04-03-2018, 02:13 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

Most users report better braking than others on...

Most users report better braking than others on market.

Are you positive that the esc itself is showing indication of full brake (solid orange when at full brake) and that your radio does not...
Forum: Radio and Electronics
03-22-2018, 02:10 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

Yes it will, including with our truggy motor

Yes it will, including with our truggy motor
Forum: Radio and Electronics
03-20-2018, 05:36 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

For 1/8 esc, it is being worked on at full...

For 1/8 esc, it is being worked on at full throttle, testing now.

For firmware, a new version is also being worked on for both escs. I am unsure if reverse will be remapped. Everything is being...
Forum: Radio and Electronics
03-18-2018, 02:11 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

Higher torque usually means less rpms. my motors...

Higher torque usually means less rpms. my motors are between 3000-3050kv usually at 50°. Also timing will change the KV (it increases rpms per volt).

I am guessing you changed to the orange cap...
Forum: Radio and Electronics
03-18-2018, 09:11 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

I run 30/75 gearing on the yz2/b6/xb2 internal...

I run 30/75 gearing on the yz2/b6/xb2 internal ratio and motor timed at 50° measured on an analyzer don’t care about amps. I run the puht rotor #4144 and the HV 30mm fan (very important in my...
Forum: Radio and Electronics
03-12-2018, 10:14 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

Might have some things being tried....🤔

Might have some things being tried....🤔
Forum: Radio and Electronics
02-26-2018, 06:15 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

You should not have any issue with the fans. ...

You should not have any issue with the fans.

As far as timing on motor 30-35 should be good,

Esc settings a higher throttle frequency will help smooth out that much motor, for brakes you will...
Forum: Radio and Electronics
02-25-2018, 01:51 PM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

I don't know what he did to fix it, he hasn't...

I don't know what he did to fix it, he hasn't said. 95% of the time the prolink looping back means it needs a firmware reflash on the esc.

You should not have any issues with that setup
Forum: Radio and Electronics
02-25-2018, 05:43 AM
Replies: 1,962
Views: 422,276
Posted By Baja-Boy

Reverse polarity almost always damages the...

Reverse polarity almost always damages the internal components. I would recommend sending the unit in for repair.

On a side note, the 3 capacitor bank will work, it is just not necessary.
Showing results 1 to 25 of 303
 
Page 1 of 13
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.