Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Search: Posts Made By: Rockin G
Showing results 1 to 16 of 16
Search took 0.01 seconds.
Forum: Nitro On-Road
11-02-2017, 11:49 AM
Replies: 2,732
Views: 479,691
Posted By Rockin G

http://www.redrc.net/2017/11/serpent-cobra-gt-3-1-...

http://www.redrc.net/2017/11/serpent-cobra-gt-3-1-team-edition-18th-nitro-gt-kit/
Forum: Nitro On-Road
05-26-2016, 07:54 PM
Replies: 2,732
Views: 479,691
Posted By Rockin G

Pit, thanks for the info on the flo-control...

Pit, thanks for the info on the flo-control pistons. I waited to do my build on my 3.0 E edition until the moment Marcus put them up on the rcshox. I have yet to run them, but the fit was very well.
Forum: Nitro On-Road
02-22-2015, 07:21 AM
Replies: 2,732
Views: 479,691
Posted By Rockin G

see pic for clutch PNs. I think the mention of...

see pic for clutch PNs. I think the mention of using only the front disk was If running the Buku clutch. The flywheel is a little bigger on that clutch causing the flywheel and clutch to touch. ...
Forum: Nitro On-Road
02-15-2015, 07:29 PM
Replies: 2,732
Views: 479,691
Posted By Rockin G

http://www.serpent.com/product/600040/setups/

http://www.serpent.com/product/600040/setups/
Forum: Nitro On-Road
12-13-2014, 08:31 AM
Replies: 2,732
Views: 479,691
Posted By Rockin G

Attn Buku clutch users. What is the solution for...

Attn Buku clutch users. What is the solution for the rear brake disk touching the flywheel. It doesn't appear to affect performance, however my flywheel is now completely clear of the grooves and...
Forum: Nitro On-Road
09-03-2014, 09:25 PM
Replies: 2,732
Views: 479,691
Posted By Rockin G

I don't think they (Walmart) are actually selling...

I don't think they (Walmart) are actually selling them. They are just providing the advertisement in their market place. Kinda like the Amazon store. I'm sure they get a cut of the money by...
Forum: Nitro On-Road
07-12-2014, 10:58 AM
Replies: 2,732
Views: 479,691
Posted By Rockin G

So you are saying half a turn 5 times? Which...

So you are saying half a turn 5 times? Which equals 2.5 turns? It used to shift fine at 5.5 turns. The manual says 5 1/2 turns. Never heard of writing it the way you mentioned. Yours shifts at...
Forum: Nitro On-Road
07-12-2014, 07:23 AM
Replies: 2,732
Views: 479,691
Posted By Rockin G

While we're on this subject, I recently had to...

While we're on this subject, I recently had to replace the 2 speed housing. Since then it seems to me like it is stuck in 2nd gear. No shifting, sluggish off the line then about mid rpm it gets...
Forum: Nitro On-Road
07-11-2014, 09:56 AM
Replies: 2,732
Views: 479,691
Posted By Rockin G

How do I visibly tell version 1 of version 2...

How do I visibly tell version 1 of version 2 diff? And the spacers that are needed or not needed, depending on the version, is that internal or behind the out drives?
Forum: Nitro On-Road
07-07-2014, 07:30 PM
Replies: 2,732
Views: 479,691
Posted By Rockin G

What changes would you make if the track is...

What changes would you make if the track is slippery? The club we race at is a temporary parking lot kinda deal. We actually alternate locations every month. One track is good with Paolos set up. ...
Forum: Nitro On-Road
06-20-2014, 09:17 PM
Replies: 2,732
Views: 479,691
Posted By Rockin G

Yes, the diff comes out, but no need to actually...

Yes, the diff comes out, but no need to actually open the diff itself. Just pull the diff out, making note of which way the diff is when you take it out. Would be easy to put it in backwards and...
Forum: Nitro On-Road
06-20-2014, 07:20 PM
Replies: 2,732
Views: 479,691
Posted By Rockin G

And if that set screw is tight, you should also...

And if that set screw is tight, you should also check the set screw for the pinion in front too. I've found mine loose before, though never to the point that you described, so it is just a thought.
Forum: Nitro On-Road
05-07-2014, 06:54 AM
Replies: 2,732
Views: 479,691
Posted By Rockin G

Got it, thanks guys. Ended up with a screw...

Got it, thanks guys. Ended up with a screw driver slightly spreading the slot and then it finally relinquished is hold.
Forum: Nitro On-Road
05-06-2014, 07:22 PM
Replies: 2,732
Views: 479,691
Posted By Rockin G

I got this car second hand, going through it and...

I got this car second hand, going through it and freshening up fluid etc...At the risk of sounding like an idiot, how the heck do I get the metal shock cups off? Do I have to unscrew the rod end?
Forum: Nitro On-Road
04-05-2014, 07:51 PM
Replies: 2,732
Views: 479,691
Posted By Rockin G

Guys, if you hear of a nice roller, shoot me a...

Guys, if you hear of a nice roller, shoot me a PM. The one above sold already. Just want to try something new. Will be selling current car soon as I get it cleaned up and transformed into roller...
Forum: Nitro On-Road
02-14-2014, 12:59 PM
Replies: 2,732
Views: 479,691
Posted By Rockin G

Doh!!! You holdin out on me!!!

Doh!!! You holdin out on me!!!
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service