Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: tbrymer
Showing results 1 to 25 of 500
Search took 0.33 seconds.
02-13-2019, 05:45 PM
Replies: 159
Views: 16,646
Posted By tbrymer

Damn, you got a deal on that.

Damn, you got a deal on that.
02-12-2019, 08:33 PM
Replies: 327
Views: 70,328
Posted By tbrymer

Start at 3.88 and around 42-50 degrees and go...

Start at 3.88 and around 42-50 degrees and go from there.
02-12-2019, 08:25 AM
Replies: 338
Views: 51,206
Posted By tbrymer

Just out of curiosity, what size spur was he...

Just out of curiosity, what size spur was he using and do you think if he put a bigger spur on he could use a smaller pinion to get the desired ratio?
02-11-2019, 06:42 AM
Replies: 1,532
Views: 333,345
Posted By tbrymer

The only thing I did to mine was replace the...

The only thing I did to mine was replace the ballends and ball cups. Everything else was great.
02-10-2019, 07:42 PM
Replies: 929
Views: 192,806
Posted By tbrymer

I have no experience with the 13.5T or the 12.3...

I have no experience with the 13.5T or the 12.3 rotor. But you could try playing with radio settings since it appears you have the highest drive frequency and the lowest power level. For instance if...
02-10-2019, 07:05 AM
Replies: 3,898
Views: 877,339
Posted By tbrymer

Faster corner speed on high traction.

Faster corner speed on high traction.
02-04-2019, 02:13 PM
Replies: 584
Views: 85,828
Posted By tbrymer

I'm kinda wanting to win concourse:)

I'm kinda wanting to win concourse:)
02-01-2019, 06:31 PM
Replies: 2
Views: 92
Posted By tbrymer

Check in the for sale forum. There's a guy...

Check in the for sale forum. There's a guy selling a lot of parts.
01-30-2019, 07:35 AM
Replies: 929
Views: 192,806
Posted By tbrymer

Check the price again. I think I saw a different...

Check the price again. I think I saw a different price.
01-28-2019, 06:38 PM
Replies: 5
Views: 303
Posted By tbrymer

http://www.r1wurks.com With this class...

http://www.r1wurks.com

With this class sounds like you might want ceramic bearings and aluminum screws to get the most RPM.
01-28-2019, 04:35 PM
Replies: 5
Views: 280
Posted By tbrymer

I've been using one for last 5 years and still...

I've been using one for last 5 years and still going strong. I even bought an M12 and decided to sell it a year later and just keep using old faithful. LOL
01-25-2019, 06:24 PM
Replies: 3,898
Views: 877,339
Posted By tbrymer

These are very cool!

These are very cool!
01-24-2019, 03:57 PM
Replies: 41
Views: 2,389
Posted By tbrymer

+1 for R1

+1 for R1
01-20-2019, 07:56 AM
Replies: 9
Views: 897
Posted By tbrymer

Put a stiffer front sway bar:)

Put a stiffer front sway bar:)
01-16-2019, 10:22 PM
Replies: 16
Views: 639
Posted By tbrymer

Yeah, you can definitely change the sensors by...

Yeah, you can definitely change the sensors by how tight you do the screws and the order.
01-16-2019, 10:20 PM
Replies: 32
Views: 1,560
Posted By tbrymer

MaxRain makes a good point. If you only want...

MaxRain makes a good point. If you only want your analyzer to verify you accurate your sensors are you could tap between the ESC and motor. But if you want something more like the skyrc analyzer...
01-16-2019, 02:53 PM
Replies: 16
Views: 639
Posted By tbrymer

Since I've used my analyzer on a crap load of...

Since I've used my analyzer on a crap load of motors, I know that mine works to some degree. I personally won't use a sensor board if it's more than 2 degrees out of phase. The worse motor I've...
01-16-2019, 02:33 PM
Replies: 32
Views: 1,560
Posted By tbrymer

Would be nice if each phase had it's own...

Would be nice if each phase had it's own interrupt, but I'm guessing you should be able to figure that out by reading a status register that contains information on which phase. I completely agree...
01-16-2019, 02:26 PM
Replies: 16
Views: 639
Posted By tbrymer

Nope, looks like you might have a bad sensor...

Nope, looks like you might have a bad sensor board, or anaylzer:)
01-15-2019, 12:04 PM
Replies: 371
Views: 105,891
Posted By tbrymer

Just an FYI - I saw some used ones for sale on...

Just an FYI - I saw some used ones for sale on Ebay last week. Not sure if they are still there.
01-10-2019, 09:12 PM
Replies: 8,344
Views: 1,195,001
Posted By tbrymer

R1 motor and PF Corvette body for asphalt and...

R1 motor and PF Corvette body for asphalt and carpet. Never had any issues staying up with anyone.
01-06-2019, 07:36 PM
Replies: 8,344
Views: 1,195,001
Posted By tbrymer

I personally don't mind lowering the weight since...

I personally don't mind lowering the weight since most touring cars are now extremely light and I don't have to add so much weight. I know your mileage may vary.
01-01-2019, 06:49 PM
Replies: 2
Views: 134
Posted By tbrymer

A800-C01B-X-LA...

A800-C01B-X-LA (http://shop.awesomatixusa.com/index.php?route=product/product&product_id=657&search=C01B-X-LA&description=true)
01-01-2019, 09:25 AM
Replies: 338
Views: 51,206
Posted By tbrymer

I agree with trigger, I like 4.00 to 4.20 for...

I agree with trigger, I like 4.00 to 4.20 for 17.5 blinky around 48 to 50 degrees. I don't mind my motors coming off around 160-170 temp. I seem run my fastest laps at those temps, with no more...
12-31-2018, 09:39 PM
Replies: 32
Views: 1,560
Posted By tbrymer

I would check out some of the documentation on...

I would check out some of the documentation on the Microchip's website. They have a lot of information about brushless motor control using their processors with pwms.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service