Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: Oleg Babich
Showing results 1 to 25 of 500
Search took 0.17 seconds.
04-11-2021, 11:55 PM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Please use 5.1 reamer for DT1202 installed into...

Please use 5.1 reamer for DT1202 installed into steering hubs with fully tightened AT1201 nuts.
AT1201 nuts compress DT1202 at excessive tightening and the hole becomes smaller.
Alternative method...
04-09-2021, 10:21 PM
Replies: 809
Views: 212,700
Posted By Oleg Babich

DT1202 are delrin. We recommend to polish...

DT1202 are delrin.
We recommend to polish ST1207 additionally.
03-07-2021, 10:20 PM
Replies: 5,528
Views: 1,416,116
Posted By Oleg Babich

The app means AT21S0.5 balls with the 0,5mm...

The app means AT21S0.5 balls with the 0,5mm offset mounting hole.
These balls allow to mount the lower arm 0,5mm wider or narrower at the same height.
02-09-2021, 12:52 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Front/rear balance is one of the most important...

Front/rear balance is one of the most important parameter for A12 car for a driver who wants to understand his car better.
Please pay attention on the setups from Sam Isaacs. Sam is using four...
02-06-2021, 09:15 PM
Replies: 5,528
Views: 1,416,116
Posted By Oleg Babich

Note this tip to keep the thread clean: ...

Note this tip to keep the thread clean:
https://site.petitrc.com/reglages/awesomatix/P63_AssemblyTips/
Please don't hesitate to tightened these screws a bit more tight to center the conical recess...
02-05-2021, 03:33 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Yes, some lube is desirable there.

Yes, some lube is desirable there.
02-04-2021, 08:41 AM
Replies: 5,528
Views: 1,416,116
Posted By Oleg Babich

Info from the creater of this app Thimo...

Info from the creater of this app Thimo Weissbauer:
A new update for the Awesomatix Toolbox app was released today.
With Android 11, Google changed the access permissions for the memory, because...
01-19-2021, 05:35 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

"...The Spherical Contact Shims set can be...

"...The Spherical Contact Shims set can be installed in the rear ball joint (ST1209M) instead of the OR125 O-ring.
The SS3x4 screw in the Battery plate is not needed at thus and should be...
01-13-2021, 06:44 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Page #18 of the latest official manual. ...

Page #18 of the latest official manual.
https://site.petitrc.com/reglages/awesomatix/setupa12/
01-06-2021, 11:26 PM
Replies: 5,528
Views: 1,416,116
Posted By Oleg Babich

This is the suspension rate ( vertical force gF /...

This is the suspension rate ( vertical force gF / vertical displacement of the wheel mm ).
01-02-2021, 10:17 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Due to the increased torsional rigidity of the...

Due to the increased torsional rigidity of the steel axle the left wheel lags much less behind the right wheel compared to the carbon axle using.
With the steel axle the front wheels need much less ...
12-27-2020, 11:59 AM
Replies: 466
Views: 95,697
Posted By Oleg Babich

~F60%/R40% without additional weights in the...

~F60%/R40% without additional weights in the front bumper and on lower deck.
12-26-2020, 11:11 PM
Replies: 5,528
Views: 1,416,116
Posted By Oleg Babich

I recommend Awesomatix ToolBox App. This tool...

I recommend Awesomatix ToolBox App. This tool provides precise calculations of the spring rate and takes into account the lower arms length.
Available for Android and for Apple....
12-18-2020, 06:34 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Small correction to your pictures: the roll...

Small correction to your pictures: the roll center should be exactly on the lower face of AM1204 plate.
12-16-2020, 12:45 PM
Replies: 809
Views: 212,700
Posted By Oleg Babich

We determine the rear droop on A12 car as the...

We determine the rear droop on A12 car as the distance that the rear damper (or ST1203) can move down from the neutral position till the droop screw will start stop such movement.
At 10,0mm droop...
12-16-2020, 01:12 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Please check the picture and note what we mean...

Please check the picture and note what we mean under "rear droop" on A12.
This is the distance between the top end of the SS3X10 set screw and ST1203 surface.
This value has the direct geometric...
12-10-2020, 06:49 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Please note that the ID of DT1202 should be...

Please note that the ID of DT1202 should be 5,10mm. Not 5,0 mm.
Our factory is using 5,10 mm reamer at production of these parts.
11-18-2020, 01:11 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

This is true with the most common settings for...

This is true with the most common settings for A12.
But the "exotic" settings are also possible and interesting to try.
One of them: Add at least +2,5mm more shims under C1203 holders for rising of...
11-12-2020, 12:24 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Exact amount of oil - 0,3 g or even 1 g is not so...

Exact amount of oil - 0,3 g or even 1 g is not so important. All excessive oil will go out sooner or later.
The most important is don't use too small amount of oil. Otherwice not 100% of the inner...
11-11-2020, 10:41 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

Did you used a needle per the manual to create a...

Did you used a needle per the manual to create a channel for the excessive oil?
I don't see this in your list of the stuff used. But this is the main tool there.
10-24-2020, 09:02 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

ST1207 tubes are made of very hard (for...

ST1207 tubes are made of very hard (for durability against abrasion) but breakable bearing chrome steel.
Please be careful and do not squeeze them too much at polishing.
10-23-2020, 08:50 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

SS3X4 set screw near middle ball joint is to keep...

SS3X4 set screw near middle ball joint is to keep the distance between two parts of chassis. O-ring surrounding this ball joint can't keep full compression load that exists there. Ball joint also...
10-22-2020, 05:42 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

We still didn't prepared justified...

We still didn't prepared justified recommendations for L/R balance technique for A12.
This car consists of two almost equivalent big parts connected via ball joints.
I think every of these two big...
10-19-2020, 12:09 PM
Replies: 809
Views: 212,700
Posted By Oleg Babich

First of all please check orientation of DT1202...

First of all please check orientation of DT1202 plastic washers.
Properly installed DT1202 and fully screwed AT1201 nuts will provide ~ 13,8mm total height of the steering blocks.
...
10-19-2020, 04:43 AM
Replies: 809
Views: 212,700
Posted By Oleg Babich

What do you mean under "built as per kit"? How...

What do you mean under "built as per kit"?
How many shims are under and over steering blocks?
1..7 shims can be on top with 0...6 shims under steering block according to the manual.
...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.