R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: shadowracer24
Showing results 1 to 25 of 500
Search took 0.05 seconds.
10-11-2022, 02:47 PM
Replies: 280
Views: 47,207
Posted By shadowracer24

It is possible to remove without taking off the...

It is possible to remove without taking off the bulkhead but your gonna need a thin wrench to fit under the arm and go around the ball nut. I have an old schmacher wrench that came in a mi5 and works...
10-09-2022, 03:54 PM
Replies: 280
Views: 47,207
Posted By shadowracer24

Got mine on Friday and had it built and race...

Got mine on Friday and had it built and race ready by sunday. The manuel can be very confusing and not very clear on some sections so take your time building. At first I wasnt very impressed with the...
09-17-2022, 01:03 PM
Replies: 3,144
Views: 913,984
Posted By shadowracer24

I haven't had that issue with mine but you could...

I haven't had that issue with mine but you could use a small dab of shoe goo at the top to hold it on.
09-12-2022, 01:20 PM
Replies: 3,144
Views: 913,984
Posted By shadowracer24

Its probably a good idea to glue the edge of all...

Its probably a good idea to glue the edge of all the graphite pieces. I found a few spots on mine where it was delaminating where the screw holes was close to the edge of the piece. Better safe than...
09-08-2022, 07:28 AM
Replies: 3,144
Views: 913,984
Posted By shadowracer24

Lol I thought you was talkin about the pivot ball...

Lol I thought you was talkin about the pivot ball for the rear pod. Yeah those are plastic but they are a hard plastic. The manuel shows remove material on the top of the pivot ball and it took me...
09-07-2022, 05:38 PM
Replies: 3,144
Views: 913,984
Posted By shadowracer24

Oops sorry thought he was talkin about the new...

Oops sorry thought he was talkin about the new one.
09-07-2022, 02:29 PM
Replies: 3,144
Views: 913,984
Posted By shadowracer24

The pivot ball isn't plastic. The ball itself is...

The pivot ball isn't plastic. The ball itself is steel and the mounts are aluminum. There is a plastic peice that fits in the mount on the chassis the pivot ball goes into but its tough. Feels almost...
09-02-2022, 05:44 PM
Replies: 3,144
Views: 913,984
Posted By shadowracer24

Someone asked a question, I have an answer based...

Someone asked a question, I have an answer based on information given to by guess who. RC AMERICA. Thankfully they got them quicker than that. I seriously doubt me getting one from some place else...
08-27-2022, 04:08 PM
Replies: 3,144
Views: 913,984
Posted By shadowracer24

Ive heard rc america should be getting them mid...

Ive heard rc america should be getting them mid to late September. I got tired of waiting and got one from RcMart. Ordered it last friday and got it thursday.
08-05-2022, 05:57 PM
Replies: 287
Views: 67,951
Posted By shadowracer24

With the R1 start with a 88 spur and 27 to 30...

With the R1 start with a 88 spur and 27 to 30 pinion. Thats what I run on mine there depending on track bite and motor temp. Usually starts out a little loose early in the day then the bite comes up...
07-15-2022, 08:30 AM
Replies: 287
Views: 67,951
Posted By shadowracer24

I ran mine with the montech f18 body and the car...

I ran mine with the montech f18 body and the car was dailed everytime I ran it.
07-14-2022, 11:24 AM
Replies: 12
Views: 1,803
Posted By shadowracer24

Ran mine on the carpet at beachline this past...

Ran mine on the carpet at beachline this past weekend and it ran perfect. Took the win and was the fastest car in the class all day.
04-11-2022, 12:22 PM
Replies: 100
Views: 10,216
Posted By shadowracer24

Really like the changes they made to the car but...

Really like the changes they made to the car but really wish they had done the same to the battery mounting system. Still a weak spot. Oh well at least the system I made will transfer over easily.
04-06-2022, 08:43 AM
Replies: 280
Views: 47,207
Posted By shadowracer24

The stamper might have had a little to much saki...

The stamper might have had a little to much saki the night before. Lol.
04-05-2022, 11:48 AM
Replies: 152
Views: 34,179
Posted By shadowracer24

I have been wanting to do the same thing but...

I have been wanting to do the same thing but couldn't figure out how to use the aluminum mount. Did you mill it out?
02-25-2022, 09:56 AM
Replies: 3,144
Views: 913,984
Posted By shadowracer24

Anyone heard when the 22 version is being...

Anyone heard when the 22 version is being released since I can't find a x21 anywhere.?
01-09-2022, 05:42 PM
Replies: 287
Views: 67,951
Posted By shadowracer24

Yep that's it.

Yep that's it.
01-09-2022, 11:01 AM
Replies: 287
Views: 67,951
Posted By shadowracer24

It's to narrow in the body to fit these newer...

It's to narrow in the body to fit these newer cars. You would probably end up hacking it all to hell to get it to fit.
01-09-2022, 10:59 AM
Replies: 287
Views: 67,951
Posted By shadowracer24

The dampener set if you haven't gotten it yet. It...

The dampener set if you haven't gotten it yet. It diffinately helps on rough asphalt.
01-04-2022, 12:35 PM
Replies: 287
Views: 67,951
Posted By shadowracer24

Anytime bud. Always happy to help. I love how...

Anytime bud. Always happy to help. I love how this car drives on carpet and like helping others get the same fun with it. It can be a little frustrating to get set right but once you get there this...
01-03-2022, 01:21 PM
Replies: 287
Views: 67,951
Posted By shadowracer24

The part number for the heavy duty posts is...

The part number for the heavy duty posts is u8161. You can get them at discount rc store. There really isn't a heavy duty upper deck but different straps for the front that change the camber and...
12-01-2021, 08:25 PM
Replies: 287
Views: 67,951
Posted By shadowracer24

The only change I made was I ran a trinity x...

The only change I made was I ran a trinity x factor motor and 96 spur. Everything else the same. I have the fan mounted to the back of the car just behind the axle but plan to move it above. Didn't...
11-30-2021, 10:53 AM
Replies: 287
Views: 67,951
Posted By shadowracer24

Took the TQ and win this past weekend at Race to...

Took the TQ and win this past weekend at Race to the birds points series at Beach line raceway in cocoa Florida. This earned me an entry to the Snowbird nationals this year which I am really excited...
10-15-2021, 09:53 AM
Replies: 2,633
Views: 266,760
Posted By shadowracer24

Yeah that's the copperhead 12. It's the latest...

Yeah that's the copperhead 12. It's the latest version that came out before they stopped making it. It's still a very competitive car to this day. I still have some good races with mine in GT 12 here...
10-12-2021, 05:44 PM
Replies: 2,633
Views: 266,760
Posted By shadowracer24

Can you post some pictures. I have a few...

Can you post some pictures. I have a few different versions of that car and could possibly tell you which one you have.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2022 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.