Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: rc_square24
Showing results 1 to 25 of 500
Search took 0.58 seconds.
05-13-2018, 10:56 AM
Replies: 427
Views: 101,400
Posted By rc_square24

TQ Racing stocks special (7-digit part number)...

TQ Racing stocks special (7-digit part number) spares for past EVO/TRF cars, but they don't seem to have any for the EVO7 yet.

http://www.tqracing.com
05-01-2018, 02:03 AM
Replies: 3,974
Views: 731,526
Posted By rc_square24

Are your referring to the diff bearings? Try...

Are your referring to the diff bearings? Try flipping them around on a spool/diff and pull on the holder to release the bearing from it.
04-30-2018, 06:27 AM
Replies: 1,788
Views: 468,426
Posted By rc_square24

I agree that for bashing the CVDs would be fine,...

I agree that for bashing the CVDs would be fine, but for an XV01 in rally mode the ride height puts the driveshafts at a larger angle and this may create a lot of chatter during steering.

And...
04-28-2018, 03:44 AM
Replies: 1,788
Views: 468,426
Posted By rc_square24

The parts for the front DCJs are as follows: ...

The parts for the front DCJs are as follows:
42239 42mm DCJ Swing Shafts
42218 DCJ Wheel Axles
42219 DCJ Joint Housings
42221 DCJ Joints
04-28-2018, 01:18 AM
Replies: 427
Views: 101,400
Posted By rc_square24

Hey guys, just reporting back on the issue of the...

Hey guys, just reporting back on the issue of the cracking TB04 diff cases as discussed a couple of pages back.

I've gone around to bore out the screw holes to 1.85mm diameter, formed threads by...
04-02-2018, 03:34 AM
Replies: 427
Views: 101,400
Posted By rc_square24

I have yet to try it, but what I mean is that...

I have yet to try it, but what I mean is that it's not the thickness of the walls are that are causing the cracks, it's cracking there because it's the weakest area (relative to the outside edge). I...
04-02-2018, 02:14 AM
Replies: 427
Views: 101,400
Posted By rc_square24

The screw holes on the TB diff cases are not...

The screw holes on the TB diff cases are not threaded. Before assembling the diff and filling oil, it is recommended that you pre-thread them to make it easier to tighten and ensuring that the screw...
03-30-2018, 03:16 AM
Replies: 1,763
Views: 549,673
Posted By rc_square24

Hey guys, looking for some advice here. I've...

Hey guys, looking for some advice here.

I've had a few runs on my TT02 and I noticed that it has unequal on power steering. It tends to push to the left much more than it does to the right, it is...
03-27-2018, 10:09 AM
Replies: 427
Views: 101,400
Posted By rc_square24

I think I have the second batch? When I...

I think I have the second batch? When I backordered it was expected for March 16.

The tag on my packaging says 2.0mm but the lower deck is actually 2.25mm on my caliper.

Both sets of the upper...
03-27-2018, 06:22 AM
Replies: 427
Views: 101,400
Posted By rc_square24

New parts available from PSM, shock towers and...

New parts available from PSM, shock towers and 2.0mm upper decks for all 3 layouts!

https://www.psmfactory.com/products/optionals/tamiya/tb-evo7/#shop
03-23-2018, 10:47 PM
Replies: 427
Views: 101,400
Posted By rc_square24

Received my PSM Chassis in the mail. Looking good...

Received my PSM Chassis in the mail. Looking good and I'm sure quality will be top notch....
03-22-2018, 01:48 AM
Replies: 427
Views: 101,400
Posted By rc_square24

Correct it should be RCLab:lol:

Correct it should be RCLab:lol:
03-21-2018, 06:34 AM
Replies: 427
Views: 101,400
Posted By rc_square24

Got an update from Facebook by RCLab that he's...

Got an update from Facebook by RCLab that he's received a chassis sample from his supplier. Also mentioned of an interesting idea he has for a possible top deck, which I hope would go into...
03-18-2018, 12:09 AM
Replies: 1,177
Views: 329,311
Posted By rc_square24

I believe so, I still see recent new arrivals of...

I believe so, I still see recent new arrivals of stock in HK (physical) hobby shops.

RCJaz has them, but my advice from previous experience with them is to always email to ask if its actually in...
03-17-2018, 09:59 PM
Replies: 427
Views: 101,400
Posted By rc_square24

Just saw on the facebook page of a HK hobby shop...

Just saw on the facebook page of a HK hobby shop "RCTEC Racing HK" that an EVO7 carbon chassis is now available. This shop is the same source of the limited run of steel bevel gear sets when the EVO6...
03-15-2018, 07:32 AM
Replies: 2,651
Views: 492,974
Posted By rc_square24

The TB04 uses a different steering system than...

The TB04 uses a different steering system than the TB EVO6.

TRF419 would be closer but it's still missing the off-center hole for the servo steering turnbuckle.
03-10-2018, 09:21 PM
Replies: 427
Views: 101,400
Posted By rc_square24

Ok I've found an easier way to remove them once...

Ok I've found an easier way to remove them once in the gearbox, using a 1.4mm flat screwdriver inserted in either of the gaps, turn the driver and the clip will fly off.

Meanwhile I'm searching...
03-10-2018, 10:05 AM
Replies: 427
Views: 101,400
Posted By rc_square24

Is there an easy way or tool to remove the eclips...

Is there an easy way or tool to remove the eclips off the bevel gears of the input shafts once there in the gearbox?

The Tamiya tool isn't that good for most cases and here it can't even be used.
03-10-2018, 01:25 AM
Replies: 1,763
Views: 549,673
Posted By rc_square24

Just built my TT02 a few weeks ago. I got the...

Just built my TT02 a few weeks ago. I got the chassis from the 99' Impreza kit which I originally bought for its rereleased body only, left the car unbuilt until I started running with a group of...
03-09-2018, 07:39 PM
Replies: 699
Views: 143,103
Posted By rc_square24

I'm just a bit confused as the product info of...

I'm just a bit confused as the product info of 54790 says to use with 54000 (M-chassis dampers), 42273 (TRF Short), 42291 (M-chassis BB)
03-09-2018, 09:16 AM
Replies: 699
Views: 143,103
Posted By rc_square24

Can anyone give me a lowdown on the difference...

Can anyone give me a lowdown on the difference between the newer 54790 shock towers and the older 54761/54762 pieces that came out earlier?

Does the 54790 eliminate the need to change shock shafts...
03-09-2018, 09:12 AM
Replies: 427
Views: 101,400
Posted By rc_square24

I'm considering using those adhesive chassis...

I'm considering using those adhesive chassis protection sheets I got from Tamiya, marking and punching the screw holes with a hole puncher.
03-09-2018, 09:09 AM
Replies: 427
Views: 101,400
Posted By rc_square24

If I recall the last time when I checked, the...

If I recall the last time when I checked, the chassis plate was a standalone (I could be wrong and missed seeing the stiffeners listed), and there was a separate product page for the front stiffener...
03-09-2018, 08:33 AM
Replies: 427
Views: 101,400
Posted By rc_square24

Hmm a few days ago I saw that they have the...

Hmm a few days ago I saw that they have the stiffeners available separately (can't remember for which layout is was).

Now they only have the chassis plate set with A and B stiffeners.

How is...
03-03-2018, 04:00 AM
Replies: 427
Views: 101,400
Posted By rc_square24

Just sent RClabhk a facebook message for the...

Just sent RClabhk a facebook message for the chassis plate, I hope he can still take my order. :nod:

Haven't got my car yet but don't wanna miss out on this batch.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Terms of Service