Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: orci77
Showing results 1 to 25 of 86
Search took 0.02 seconds.
03-09-2012, 10:58 PM
Replies: 5,880
Views: 399,095
Posted By orci77

Do these girls know that they cause partial...

Do these girls know that they cause partial amnesia on RC Car drivers worldwide?
03-04-2012, 10:18 AM
Replies: 4,239
Views: 650,263
Posted By orci77

Thats what I would guess because on the '12 shock...

Thats what I would guess because on the '12 shock towers Xray moved the holes closer to the bottom edge.
03-03-2012, 04:13 AM
Replies: 4,239
Views: 650,263
Posted By orci77

I use the Xray shocks # 308306-O. Tried the...

I use the Xray shocks # 308306-O.
Tried the Tamiya TRFs on my T2'009 but the top joint is too short so the top of the shock touches the shock tower and didnt move freely. Since I didnt want to...
03-02-2012, 09:10 AM
Replies: 4,239
Views: 650,263
Posted By orci77

They should survive crashes. Only once a friend...

They should survive crashes. Only once a friend of mine had a brocken shock body. But this is one case in over 3 years. So dont bother about this.

I upgraded to alu shocks too.
They feel better....
02-29-2012, 12:52 PM
Replies: 4,239
Views: 650,263
Posted By orci77

In Xray forum it was said that he was NOT running...

In Xray forum it was said that he was NOT running the 2,0mm.
02-24-2012, 11:27 PM
Replies: 5,880
Views: 399,095
Posted By orci77

I see. I just thought because of the nice...

I see. I just thought because of the nice pictures you take you are the one. But wait! Your wife takes the pcitures. I was wrong ;) :D
02-24-2012, 10:31 AM
Replies: 5,880
Views: 399,095
Posted By orci77

Well, it looks like I had the same dream :D ...

Well, it looks like I had the same dream :D

@Ligthfoot: Do you design the shirts? The new design looks really like art. How long does it take to make such a design. I guess it was ask in the past:...
02-14-2012, 09:56 AM
Replies: 4,239
Views: 650,263
Posted By orci77

This is enough:...

This is enough: http://www.teamxray.com/teamxray/products/proddesc.php?prod_id=3978&kategoria=&catName=Diff.%20Gasket%20%284%29
Or you take two of them if one doesnt work.
02-11-2012, 12:34 AM
Replies: 4,239
Views: 650,263
Posted By orci77

You mean the universal shaft? I had this too. I...

You mean the universal shaft?
I had this too. I pushed the pin several times trough the drive axle till I can push it through with my fingers. After that the bending was gone.
02-11-2012, 12:32 AM
Replies: 4,239
Views: 650,263
Posted By orci77

So Exotek is doing Tamiya style lower suspension...

So Exotek is doing Tamiya style lower suspension holders?
Where is the advantadge in this solution compare to the Xray one?
02-10-2012, 09:29 AM
Replies: 4,239
Views: 650,263
Posted By orci77

Had to do the same on my car and a friend on his...

Had to do the same on my car and a friend on his car too.
02-09-2012, 10:35 AM
Replies: 4,239
Views: 650,263
Posted By orci77

The o-ring gets wider, correct? Last time I cut...

The o-ring gets wider, correct?
Last time I cut out what was too much and put it in with some green slime and no leakage.
But as said before some team drivers dont use the o-ring at all. Also heard...
02-04-2012, 10:00 PM
Replies: 4,239
Views: 650,263
Posted By orci77

Why do you wand to spend money if you dont know...

Why do you wand to spend money if you dont know if it works?

If it is really a chassis from Martin Hudy it must be a prototype. I wonder how someone can sell it...
01-30-2012, 11:12 AM
Replies: 4,239
Views: 650,263
Posted By orci77

Sounds strange to me. I had to put 0,4mm shim...

Sounds strange to me.
I had to put 0,4mm shim in left rear and now I have 3. And this was on the kit of a friend of mine exactly the same.
01-22-2012, 03:24 AM
Replies: 4,239
Views: 650,263
Posted By orci77

What is this combo?

What is this combo?
01-16-2012, 10:34 AM
Replies: 4,239
Views: 650,263
Posted By orci77

Did you tried the tech tip from Xray:...

Did you tried the tech tip from Xray: http://forum.teamxray.com/viewtopic.php?p=41851&sid=abadda687f6ab3c99e82dcce099110ed#p41851
Worked for me. Didnt have to ream or take off material from anywhere.
01-11-2012, 01:00 PM
Replies: 4,239
Views: 650,263
Posted By orci77

As long as you use the same method you are fine. ...

As long as you use the same method you are fine.
If you measure different from day to day you get lost.
Also comparison is difficult because it is not clear how and where exactly everybody...
01-11-2012, 12:41 PM
Replies: 5,880
Views: 399,095
Posted By orci77

Come on! Design a new shirt so we have a better...

Come on! Design a new shirt so we have a better excuse to check the fotos :D

P.S.: If it is too much work to design a new shirt than just continue to make pictures... ;)
12-31-2011, 02:03 AM
Replies: 4,239
Views: 650,263
Posted By orci77

I bend my first hudy spring steel shaft some...

I bend my first hudy spring steel shaft some weeks ago. I was on full throttle (17.5T boost) on the straight. There is a 90 turn that you go full. So my steering was fully on the left and then a car...
12-29-2011, 10:00 AM
Replies: 4,239
Views: 650,263
Posted By orci77

You are right: driving style makes a big...

You are right: driving style makes a big difference. The same setup on same cars on same track doesnt work for everybody.

I started with 700. My friend used directly 1000. After speaking with a...
12-29-2011, 03:09 AM
Replies: 4,239
Views: 650,263
Posted By orci77

Mine never leaked. What oil did you used? Are you...

Mine never leaked. What oil did you used? Are you sure you put the right oring at the right place?
As said the oring should "grow" a little when in contact with the silicon oil.
12-29-2011, 03:06 AM
Replies: 4,239
Views: 650,263
Posted By orci77

When I changed to Xray (T2'009) I was impressed...

When I changed to Xray (T2'009) I was impressed because you feel every change on the car. For me this is by now typical for Xray. Obviously same on the T3'012.

The body makes a big difference to...
12-28-2011, 04:14 AM
Replies: 15,587
Views: 3,560,764
Posted By orci77

How cool is this? And +1 for jack & coke

How cool is this?
And +1 for jack & coke
12-28-2011, 04:06 AM
Replies: 4,239
Views: 650,263
Posted By orci77

Hudy Spring Steel. You normally need a very...

Hudy Spring Steel.
You normally need a very heavy crash to bend them.
12-26-2011, 01:40 AM
Replies: 1,718
Views: 319,097
Posted By orci77

I agree it would be nicer if it works...

I agree it would be nicer if it works automatically. But also ahint in the manual would be good.

Your "GLOVE" is a cool idea.
Showing results 1 to 25 of 86
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.