R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: Kave
Showing results 1 to 25 of 500
Search took 0.68 seconds.
01-26-2022, 10:22 AM
Replies: 432
Views: 60,215
Posted By Kave

As I've said before, just cut to the lowest line...

As I've said before, just cut to the lowest line on the Akura and you won't have any issues. It's completely legal and will be just fine on any track.
01-24-2022, 12:27 PM
Replies: 432
Views: 60,215
Posted By Kave

I've been using the lowest molded in cut line on...

I've been using the lowest molded in cut line on the Montec Akura.
01-13-2022, 09:39 AM
Replies: 49,241
Views: 5,980,606
Posted By Kave

You cannot set circles on the track with a spool...

You cannot set circles on the track with a spool because both rear tires are going to try to move the same distance due to the solid axle despite the fact that they are not actually traveling the...
01-12-2022, 01:22 PM
Replies: 49,241
Views: 5,980,606
Posted By Kave

Increase

Increase
01-12-2022, 01:22 PM
Replies: 49,241
Views: 5,980,606
Posted By Kave

It is always measured on the INSIDE wheel.

It is always measured on the INSIDE wheel.
12-30-2021, 01:47 PM
Replies: 432
Views: 60,215
Posted By Kave

Perfect rule set!

Perfect rule set!
12-22-2021, 09:46 AM
Replies: 432
Views: 60,215
Posted By Kave

I agree with all of this. There is NO...

I agree with all of this.

There is NO question that GT12 on rubber tires is significantly easier for "most" people to drive because everything happens at a slower rate. A similar car with the same...
12-20-2021, 08:06 AM
Replies: 432
Views: 60,215
Posted By Kave

Bullfrog - Are you in or out for rubber tires?...

Bullfrog - Are you in or out for rubber tires? The future is here!
12-17-2021, 07:11 AM
Replies: 432
Views: 60,215
Posted By Kave

We have actually been gluing the tires. It's not...

We have actually been gluing the tires. It's not needed but it makes it so you can drive the cars as hard as you want from the very start.

The tires work just fine without glue, they just work a...
12-15-2021, 11:14 AM
Replies: 1
Views: 139
Posted By Kave

I have one that has about 20 laps on it because...

I have one that has about 20 laps on it because foam tc never took off again. PM me your address or phone number and I'll send some pics later tonight.
12-14-2021, 09:19 AM
Replies: 432
Views: 60,215
Posted By Kave

Bullfrog - What will you do if the biggest race...

Bullfrog - What will you do if the biggest race in Florida (the Snowbirds) runs rubber tire GT12? Will you race with us or will you be too busy posting on rctech?
12-03-2021, 07:07 AM
Replies: 969
Views: 285,530
Posted By Kave

The actual measured camber at the wheel will...

The actual measured camber at the wheel will generally be one-half of whatever you set it at on the Hudy setup station. If you set it to 1* on the Hudy it will measure .5* on the wheel every time.
11-30-2021, 07:04 AM
Replies: 49,241
Views: 5,980,606
Posted By Kave

It's the same foam that is used on JFT specs.

It's the same foam that is used on JFT specs.
10-26-2021, 10:40 AM
Replies: 969
Views: 285,530
Posted By Kave

We are tightening it down before reaming and then...

We are tightening it down before reaming and then measuring that number so that it can be reassembled with Loctite to the same number. But the caps are definitely cranked down tight so they don't...
10-22-2021, 07:16 AM
Replies: 969
Views: 285,530
Posted By Kave

You can just use that 5.1mm reamer and ream out...

You can just use that 5.1mm reamer and ream out the bushings rather than polish the tubes. You will get a similar result for a lot less work.
10-11-2021, 10:44 AM
Replies: 49,241
Views: 5,980,606
Posted By Kave

Andrew Knapp

Andrew Knapp
08-05-2021, 09:30 AM
Replies: 49,241
Views: 5,980,606
Posted By Kave

We ran 105-108mm rollout at Snowbirds, I know...

We ran 105-108mm rollout at Snowbirds, I know others were under 110mm as well. Some may have been higher.
07-16-2021, 12:36 PM
Replies: 969
Views: 285,530
Posted By Kave

Same for me.

Same for me.
07-14-2021, 12:59 PM
Replies: 1,012
Views: 232,362
Posted By Kave

You know he's talking about you, right Marcos?

You know he's talking about you, right Marcos?
06-01-2021, 02:28 PM
Replies: 969
Views: 285,530
Posted By Kave

You need to be careful when talking about camber...

You need to be careful when talking about camber on the A12. The camber settings with the prealigned holes provided by Awesomatix will almost always be lower than measuring on a Hudy.

As a general...
04-30-2021, 01:05 PM
Replies: 1,035
Views: 195,897
Posted By Kave

Yes you do.

Yes you do.
04-27-2021, 03:11 PM
Replies: 49,241
Views: 5,980,606
Posted By Kave

That used to be true because the 6000mah...

That used to be true because the 6000mah batteries over the last couple of years held their voltage longer for some reason. However, for at least the past 2 race seasons this hasn't been the case and...
04-23-2021, 08:01 AM
Replies: 969
Views: 285,530
Posted By Kave

This is not good advice in my opinion. We have...

This is not good advice in my opinion. We have had a lot more luck running the battery tray ride height over the main chassis ride height by 3-4/10ths of a mm.

Doing so just makes the car work...
04-23-2021, 08:00 AM
Replies: 969
Views: 285,530
Posted By Kave

I ran 30k at Snowbirds in Can-Am 1/12th scale and...

I ran 30k at Snowbirds in Can-Am 1/12th scale and then I ran 40k in 17.5 open motor at the Mile High Indoor Champs. Both cars were really good. In stock I've not ran over 50k even on much lower level...
02-11-2021, 11:17 AM
Replies: 48
Views: 5,598
Posted By Kave

Did you use the same glue process? Did you apply...

Did you use the same glue process? Did you apply the same amount of glue?

Glue can be even more important than the actually truing job. You want to make sure you have the same diameter and...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.