Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: Worst87
Showing results 1 to 25 of 72
Search took 0.02 seconds.
06-22-2017, 03:23 AM
Replies: 7,552
Views: 1,560,169
Posted By Worst87

Question for yokomo experts: Do bd8 shock towers...

Question for yokomo experts: Do bd8 shock towers fit the bd7 16 and vice versa?
If yes i can buy the new "big diff/spool" pulley conversion for my 16...
04-27-2017, 07:30 AM
Replies: 1,835
Views: 488,669
Posted By Worst87

FLOW X Setup for 13.5T boosted

Hi Rc racers!
I have a new flow x and LRP 13.5T motor. I want to drive boosted so does someone got settings i can start off with?
04-27-2017, 07:27 AM
Replies: 1,835
Views: 488,669
Posted By Worst87

Its not compatible with the old usb bridge. A new...

Its not compatible with the old usb bridge. A new one isnt published yet.
03-06-2017, 01:41 PM
Replies: 15
Views: 12,426
Posted By Worst87

HPI silver is a quite progressive spring! ...

HPI silver is a quite progressive spring!
http://www.rcweb.de/index.php/Thread/17416-Federmessung/?pageNo=1

In this german forum i (The worst) have made some graphics and comparisons...
Maybe...
02-13-2017, 12:01 AM
Replies: 1,731
Views: 481,607
Posted By Worst87

It moves up and down in heave motion. Typically a...

It moves up and down in heave motion. Typically a double wishbone with shorter upper link the roll Center lowers during compression. And vice versa

But if the car rolls the roll center moves...
02-02-2017, 04:44 AM
Replies: 157
Views: 59,432
Posted By Worst87

Lsf 0.7 2 color rattlecan design thin layers...

Lsf 0.7
2 color rattlecan design thin layers and stock wing: 82 g
11-22-2016, 12:05 AM
Replies: 4,583
Views: 984,947
Posted By Worst87

Hi Professor They are 0.5mm lower. On very...

Hi Professor
They are 0.5mm lower. On very hard hits the inserts can crack/pop out. Happened once during outdoor season. Overall very happy
10-25-2016, 01:11 AM
Replies: 910
Views: 202,421
Posted By Worst87

No! Raising inner upper link lowers roll...

No!
Raising inner upper link lowers roll center. raising outer (hub) pickup point raises the roll center.
10-05-2016, 12:30 AM
Replies: 587
Views: 117,607
Posted By Worst87

Yes. I`ve got the vbc tbbs shocks and as they...

Yes. I`ve got the vbc tbbs shocks and as they have quite high damping with 3 hole pistons and 350 oil i rebuilt them with 4 hole and 450 and its more moderate now. But still harder damping compared...
10-04-2016, 04:55 AM
Replies: 587
Views: 117,607
Posted By Worst87

Hi tlp, Less holes or smaller hole diameter...

Hi tlp,

Less holes or smaller hole diameter and lighter oil gives same low speed dampning but higher high speed damping. Somewhere on petitrc there was a nice comparison chart...
09-20-2016, 06:08 AM
Replies: 1,054
Views: 289,845
Posted By Worst87

Which springs was Ronald using at the worlds? ...

Which springs was Ronald using at the worlds?
Btw: seems like no news so far...
09-15-2016, 09:01 PM
Replies: 7,552
Views: 1,560,169
Posted By Worst87

Hi rctrains, as the bd7 is a 1/10th scale tc...

Hi rctrains,
as the bd7 is a 1/10th scale tc you should buy wheels for this scale. Typical brands are sweep ride sorex...
08-23-2016, 09:53 PM
Replies: 7,552
Views: 1,560,169
Posted By Worst87

Serpent DJCs have at the inner bearing a bigger...

Serpent DJCs have at the inner bearing a bigger diameter than the outer. So definetly not Serpent
07-27-2016, 09:06 AM
Replies: 7,552
Views: 1,560,169
Posted By Worst87

Hey Rodney thanks a lot for your review! So its...

Hey Rodney thanks a lot for your review! So its not possible to change roll center height via inserts right? Still willing to order them
07-27-2016, 01:39 AM
Replies: 7,552
Views: 1,560,169
Posted By Worst87

TECHRA blocks

Hi BD7 racers. Has someone used the TECHRA blocks and give a feedback on quality, sloppy or not, and maybe durability? Would like to order them or the much more expensive samix blocks...
Thanks!
01-09-2016, 03:21 AM
Replies: 290
Views: 54,863
Posted By Worst87

No. This are 100% sure not the new serpent...

No. This are 100% sure not the new serpent shocks. look at the height/width ratio of the photo and the new serpent ones. Xray shocks!
09-14-2015, 01:55 AM
Replies: 7,552
Views: 1,560,169
Posted By Worst87

Hi Bruce, to lower your rear roll center...

Hi Bruce,

to lower your rear roll center you can:
a) put MORE shims under the upper inner link
b) put LESS shims under the upper outer link (rear hub)
c) put LESS shims under the lower inner...
09-14-2015, 01:40 AM
Replies: 732
Views: 158,005
Posted By Worst87

Hi SBH, how do you balance out the chassis...

Hi SBH,
how do you balance out the chassis left-right? Shorty is in the 240g-ish weight area i think. That means a lot of additional weight.
Which front-rear weight bias do you prefer, or have...
07-13-2015, 12:23 AM
Replies: 12
Views: 4,498
Posted By Worst87

I do know one Item in the list: The fake charger...

I do know one Item in the list: The fake charger of the imax b6
Mine smoked out the second day, so i dont recommend it!
06-27-2015, 03:35 AM
Replies: 4,583
Views: 984,947
Posted By Worst87

Just search for "3.5" in this link: ...

Just search for "3.5" in this link:
http://ets.redrc.net/2015/06/coelho-tqs-opening-qualifier-in-slovakia/
:nod:

Hard to imagine, that 0,5mm thickness difference on the shock tower is...
06-24-2015, 01:08 AM
Replies: 501
Views: 102,499
Posted By Worst87

Hi racers. Im owner of the X-8N radio for 2...

Hi racers.
Im owner of the X-8N radio for 2 weeks now. Coming from a sanwa mx-v the lower latency is just stunning. Correcting a moment of oversteer on turn in was nearly impossible before, with...
06-15-2015, 05:36 AM
Replies: 11
Views: 755
Posted By Worst87

The link which was posted by tc3team is really...

The link which was posted by tc3team is really really good!!! Thanks for sharing
06-11-2015, 11:00 PM
Replies: 45
Views: 11,133
Posted By Worst87

Would a dry lubricant keep the de-shielded clean...

Would a dry lubricant keep the de-shielded clean some runs longer compared to light oil? The oil sucks up dirt imo. I use the avid revo bearings and im quite happy with them. But havent tried dry...
06-04-2015, 02:16 AM
Replies: 1,833
Views: 386,553
Posted By Worst87

IMHO this is traction level and power dependent....

IMHO this is traction level and power dependent. Front diff should be good from mid to high traction when having low motor power like 17.5T or higher. In mod its not useful really
06-01-2015, 02:44 AM
Replies: 852
Views: 146,011
Posted By Worst87

Serpent had a good Weekend in Luxembourg ETS....

Serpent had a good Weekend in Luxembourg ETS. Julian won the stock class
Here is a chassis focus we can discuss about.
http://ets.redrc.net/2015/05/chassis-focus-julian-borowski/

Really...
Showing results 1 to 25 of 72
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.