R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
Search: Posts Made By: Danie
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Forum: Nitro Off-Road
06-14-2007, 11:05 PM
Replies: 8
Views: 1,662
Posted By Danie

I Have tried it at home and works 300%!! :nod: ...

I Have tried it at home and works 300%!! :nod:
Thanx!
Forum: Nitro Off-Road
06-13-2007, 09:53 PM
Replies: 8
Views: 1,662
Posted By Danie

Thanx, will try that tonight. :)

Thanx, will try that tonight. :)
Forum: Nitro Off-Road
06-11-2007, 12:06 PM
Replies: 2
Views: 1,166
Posted By Danie

I have the same car, with exacltly the same...

I have the same car, with exacltly the same issues.

What I did was to get the idle screw to push the slide in about 1-2mm, set the low speed flush then half a turn out(rich) and the HSN 2-3 full...
Forum: Nitro Off-Road
06-11-2007, 06:18 AM
Replies: 4
Views: 1,085
Posted By Danie

Try the following links, helped me alot!! :nod: ...

Try the following links, helped me alot!! :nod:

http://www.rchobbies.org/cars_eng-tuning.htm
http://www.rccartips.com/Nitro_Engine_Tuning_by_Josh_Cyrul.htm

Hope this helps you.
Forum: Nitro Off-Road
06-08-2007, 07:03 AM
Replies: 6
Views: 1,274
Posted By Danie

I will take a pic of the current setup and the...

I will take a pic of the current setup and the previous setup !? Maybe through this you guys can see if I did it correct. :)
Forum: Nitro Off-Road
06-08-2007, 07:00 AM
Replies: 8
Views: 1,662
Posted By Danie

Post Slipper Clutch Setup?

What is the correct or best way to set up the slipper clutch? I See some people grab the wheel and try to turn the gear to see if it tensioned enough?

:rolleyes:
Forum: Nitro Off-Road
06-08-2007, 12:35 AM
Replies: 6
Views: 1,274
Posted By Danie

I have checked the clearence on the calipers and...

I have checked the clearence on the calipers and it was a little far open. I've screwed it in till the point that a 1/4 turn will almost complete stop the truck, is this ok or too much?

The truck...
Forum: Nitro Off-Road
06-07-2007, 09:47 PM
Replies: 11
Views: 2,653
Posted By Danie

Post Bent Dogbones?

Does anybody got a good way to straiten bent dogbones, and for that matter any other bent rod on the rc:confused:
Forum: Nitro Off-Road
06-07-2007, 03:12 AM
Replies: 6
Views: 1,274
Posted By Danie

I havent check the play on the calipers, will do...

I havent check the play on the calipers, will do that tonight, thanks :). The car is 3 months old, so i dont think that the disk is worn out, but I will just make sure.

If you have to suggest what...
Forum: Nitro Off-Road
06-06-2007, 11:26 PM
Replies: 6
Views: 1,274
Posted By Danie

Post Stopping power!?

I have a HB Lightning GT10 1/10 and it really has a breaking problem. I have ajusted it at all the places where I can and still does'nt want to stop. For example if breakes is pushed full in from top...
Forum: Onroad Nitro Engine Zone
06-04-2007, 09:48 PM
Replies: 7
Views: 1,567
Posted By Danie

Pinch Test

How accurate is the pinch test?:confused:
Forum: Nitro Off-Road
06-04-2007, 09:21 PM
Replies: 6
Views: 10,580
Posted By Danie

I thougt off that and tried it last night but how...

I thougt off that and tried it last night but how do Iget the crank of the flywheel?I tried but its stuck, and i don't want to use force.:confused:

And if everything is out how do I check the...
Forum: Nitro Off-Road
06-04-2007, 07:59 AM
Replies: 6
Views: 10,580
Posted By Danie

Thank you!!

Thanks, going to try that tonight.

And congrats on the placing!!

Thanks again.:D
Forum: Nitro Off-Road
06-04-2007, 03:33 AM
Replies: 6
Views: 10,580
Posted By Danie

Unhappy Cleaning Dirt out of engine - Please Help !!

I got dirt in the motor through the filter, got off a jump and started to roll and the filter came lose, then suck few grains of sand in, it died after that.

Now my qeustion is wat is the best way...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.