R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: EMU
Showing results 1 to 25 of 500
Search took 0.20 seconds.
05-23-2020, 05:21 AM
Replies: 6,666
Views: 829,948
Posted By EMU

For battery removal, the battery clips can be...

For battery removal, the battery clips can be inserted into the openings on the bottom of the chassis to dislodge them easily.

red tool was said to be a binding stick, but it doesn't really make...
05-02-2020, 04:26 AM
Replies: 6,666
Views: 829,948
Posted By EMU

2N/3W will work on the 12C. With 22.8mm front...

2N/3W will work on the 12C. With 22.8mm front wheels, they do not rub. I cannot state for the rear height of the ASC body, I build white bodies, and mount the side clips where it provides...
05-02-2020, 04:23 AM
Replies: 440
Views: 61,383
Posted By EMU

What front tires is he using? Any glue on the...

What front tires is he using? Any glue on the sidewalls? Does he have a brass chassis?

He can try reducing the drag brake, or reducing the droop on the center shock which will transfer less mass...
04-24-2020, 10:37 PM
Replies: 6,666
Views: 829,948
Posted By EMU

As Traveler said, .5mm is pretty much the maximum...

As Traveler said, .5mm is pretty much the maximum you would want to raise the tower. I havent really needed to adjust roll center on many of my current setups, but back when I was racing with...
04-21-2020, 02:04 PM
Replies: 1
Views: 212
Posted By EMU

https://www.rctech.net/forum/micro-mini-scales/105...

https://www.rctech.net/forum/micro-mini-scales/1053858-need-instructions-gl-racing-x-power-esc.html
04-17-2020, 03:52 AM
Replies: 450
Views: 29,680
Posted By EMU

I race for MRCS, and assist with technical...

I race for MRCS, and assist with technical advice/Customer Service. I do not want to push the product and service as is often seen in the industry, but prefer for the reputation and customer...
04-16-2020, 11:52 AM
Replies: 450
Views: 29,680
Posted By EMU

Pretty sure that MX-6 uses FH-E protocol, so it...

Pretty sure that MX-6 uses FH-E protocol, so it wouldnt work with any of the micro receivers for Sanwa. MT-S is the radio to get for Sanwa. At its price point, it really cannot be beat in my...
04-16-2020, 11:19 AM
Replies: 6,666
Views: 829,948
Posted By EMU

https://youtu.be/n42_Ih2qEts This was the...

https://youtu.be/n42_Ih2qEts

This was the first race which I raced at Cruizin with RC's. They ran the skinny class, so I built a blue mini-cooper when I got there. 19mm front and rear, and 0mm...
04-15-2020, 01:53 AM
Replies: 901
Views: 62,321
Posted By EMU

What body is that on the 102mm GLR? What rear...

What body is that on the 102mm GLR? What rear and side springs do you have installed? Are you using the longer spring set for the longer shock shaft? I would think that the green or red spring...
04-15-2020, 01:38 AM
Replies: 450
Views: 29,680
Posted By EMU

For the battery, contact GL directly. They...

For the battery, contact GL directly. They should be able to send you some, but cannot post it on the site for sale. You can find them on FaceBook (preferred method of contact).

As for...
04-10-2020, 11:02 PM
Replies: 450
Views: 29,680
Posted By EMU

Most servo's are centered well from the factory,...

Most servo's are centered well from the factory, but I still recommend powering up to center before installing the servo horn.

When I drove 1/10 F1, I drove Xray, and feel that for the most part...
03-26-2020, 01:24 PM
Replies: 440
Views: 61,383
Posted By EMU

In my early time using the GLR, my go to tire...

In my early time using the GLR, my go to tire combo was KS soft rear and K20 front. I actually used LM 20 fronts trued down, and liked them best. This combo worked well with the stock chassis, and...
03-23-2020, 02:22 PM
Replies: 440
Views: 61,383
Posted By EMU

it sounds very odd that the cap stud screw would...

it sounds very odd that the cap stud screw would interfere with a 9t 64p pinion when that should place the motor as close to the differential as possible.
03-23-2020, 01:14 PM
Replies: 6,666
Views: 829,948
Posted By EMU

I would consider getting an unpainted McLaren 12C...

I would consider getting an unpainted McLaren 12C to build and try instead of the Corvette before looking to rework the suspension setup. My feeling with the vette is that it is good into the corner,...
03-19-2020, 12:00 PM
Replies: 440
Views: 61,383
Posted By EMU

Can you post a pic of the mesh?

Can you post a pic of the mesh?
03-14-2020, 12:59 AM
Replies: 6,666
Views: 829,948
Posted By EMU

Which blue are you referring to? Atomic used 3...

Which blue are you referring to? Atomic used 3 different blues... A very dark blue, like Kyosho early on, then a medium and an Ice blue on some parts for a couple years before they pulled out of the...
03-11-2020, 12:24 PM
Replies: 6,666
Views: 829,948
Posted By EMU

unfortunately the electronics in your RTR are not...

unfortunately the electronics in your RTR are not compatible with the ex6. You can get an ASF board and swap it. The dasmikro clone brushed board is relatively inexpensive and would be the easiest...
03-11-2020, 12:21 PM
Replies: 6,666
Views: 829,948
Posted By EMU

90 is a bit tricky to conceptualize, with the...

90 is a bit tricky to conceptualize, with the plate on the pod it is essentially reversed... however, the post is opposite the pivot. I typically used a neutral disc preload setup with a stiffer...
03-11-2020, 09:42 AM
Replies: 6,666
Views: 829,948
Posted By EMU

Typically not using the upper disc in a standard...

Typically not using the upper disc in a standard damper system
(non reversed plate like 90mm), will offer more steering. I personally prefer the top disc, as without it the rear end can be quite...
03-08-2020, 04:08 PM
Replies: 6,666
Views: 829,948
Posted By EMU

When you reversed direction, was this done by...

When you reversed direction, was this done by swapping wires or adjusting the rotation direction in the ESC settings?

I totally agree that there should be a standard pinout standard for the sensor...
03-07-2020, 12:06 AM
Replies: 440
Views: 61,383
Posted By EMU

Before I build my diff, I put a dab of purple...

Before I build my diff, I put a dab of purple thread lock on the threads of the shaft and let it dry. Then I run the nut up and down a few times and blow out any debris. This usually prevents any...
03-05-2020, 08:37 PM
Replies: 6,666
Views: 829,948
Posted By EMU

check your solder joints. Any bridge between the...

check your solder joints. Any bridge between the poles can cause issues.
03-04-2020, 04:40 PM
Replies: 440
Views: 61,383
Posted By EMU

Expo = curve, so try going negative and see how...

Expo = curve, so try going negative and see how it feels. Only you can know what is comfortable. Try extreme settings, -50 and gradually dial it back until you find a comfortable setting.
03-03-2020, 04:44 PM
Replies: 440
Views: 61,383
Posted By EMU

Have you tried a negative steering curve, or...

Have you tried a negative steering curve, or lowering the servo speed? When on the straight, the car is quite responsive, and while a mini-z can use moderate steering correction on the straight, the...
03-02-2020, 07:50 PM
Replies: 450
Views: 29,680
Posted By EMU

Great feedback. Love to hear the development...

Great feedback. Love to hear the development process you are going through. I have not had my car on track since Detroit in November. Having very limited track time lately, every time I get on...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.