R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: rcgerber
Showing results 1 to 25 of 500
Search took 0.20 seconds.
12-20-2019, 04:18 PM
Replies: 43
Views: 9,319
Posted By rcgerber

You might want to check out Panther tires, they...

You might want to check out Panther tires, they have an old school step pin tire that might work depending on your dirt type and the moisture level in the dirt.
Setup wise, you might want to try...
06-26-2019, 06:32 PM
Replies: 1,778
Views: 395,454
Posted By rcgerber

Basically the ceramic balls are harder, and...

Basically the ceramic balls are harder, and because of this they slip easier. On top of that the harder ball dig into the ring more due to the large difference as well as the tendency to run the diff...
06-24-2019, 08:49 AM
Replies: 1,778
Views: 395,454
Posted By rcgerber

Ceramic balls narrows the adjustment range. If...

Ceramic balls narrows the adjustment range. If you go back to a carbide ball you'll find it much easier to find the desired tension for your conditions.
09-28-2018, 08:58 AM
Replies: 2
Views: 2,769
Posted By rcgerber

Hit up Shon Harding of Sweetwater Raceway on...

Hit up Shon Harding of Sweetwater Raceway on facebook. Search for Sweetwater raceway and shoot him a message there. He might be a little slow to respond due to him going out of town for the next...
01-16-2018, 06:09 AM
Replies: 1,778
Views: 395,454
Posted By rcgerber

Check with mibosport. They have most parts in...

Check with mibosport. They have most parts in stock for the belt car.
11-27-2017, 08:05 PM
Replies: 5,032
Views: 1,065,599
Posted By rcgerber

The big thing that would be different between the...

The big thing that would be different between the the original and ca isn't the chassis its the 4 gear trans vs the 3 gear.
07-05-2017, 02:57 PM
Replies: 417
Views: 47,430
Posted By rcgerber

Yes and No. The track is currently closed for...

Yes and No. The track is currently closed for resurfacing, and Shon (the track owner has some family obligation he's taking care of which is delaying the resurface work. Follow Sweetwater on...
05-04-2017, 05:30 PM
Replies: 12
Views: 2,351
Posted By rcgerber

Take a look at the Pr Racing ST1 V2. It comes...

Take a look at the Pr Racing ST1 V2. It comes rear motor which might be ideal for you, but it can convert to mid motor with a few parts. It is a very durable truck with two upgrades. The steering...
04-24-2017, 06:00 AM
Replies: 853
Views: 162,928
Posted By rcgerber

Here is a picture that shows the kit to convert...

Here is a picture that shows the kit to convert the 401 in to a 4wd st.
http://www.pr-rc.com/program/product/pics/pdt_big_201411263141745.jpg
04-07-2017, 07:44 AM
Replies: 5,032
Views: 1,065,599
Posted By rcgerber

I think everything is the same except the actual...

I think everything is the same except the actual gear which uses 14 balls instead. I am basing my info on what Lee Martin's live talk on facebook.
04-07-2017, 06:51 AM
Replies: 5,032
Views: 1,065,599
Posted By rcgerber

https://www.mibosport.com/yokomo/yz-2dtm/ has all...

https://www.mibosport.com/yokomo/yz-2dtm/ has all the parts that are unique to the dtm and the dtm comes with a new 14 ball ball diff.
03-31-2017, 02:34 PM
Replies: 7
Views: 1,242
Posted By rcgerber

Prices & Classes being run?

Prices & Classes being run?
03-15-2017, 06:50 AM
Replies: 610
Views: 134,026
Posted By rcgerber

Doesn't look like it based on what you can see of...

Doesn't look like it based on what you can see of the arms.
02-16-2017, 12:18 PM
Replies: 300
Views: 46,142
Posted By rcgerber

Just put a nut on the bottom of the ball stud in...

Just put a nut on the bottom of the ball stud in the pro-block. Any 3-5mm long counter sink screw would work.
02-09-2017, 06:27 AM
Replies: 300
Views: 46,142
Posted By rcgerber

ZX, first you might want to upgrade to the 25 deg...

ZX, first you might want to upgrade to the 25 deg chassis (unless you run on carpet and want the extra steering). As for the V3mm trans, I think it is a distinct possibility that it does fit. The...
02-02-2017, 12:53 PM
Replies: 5
Views: 1,664
Posted By rcgerber

Jconcepts has one. ...

Jconcepts has one.
http://www.jconcepts.net/shop/aluminum-carbon-setting-board
01-13-2017, 08:55 AM
Replies: 43
Views: 9,319
Posted By rcgerber

http://www.casterracingparts.com/index.php?route=p...

http://www.casterracingparts.com/index.php?route=product/product&path=63_115&product_id=1083
It's available here
12-30-2016, 06:52 AM
Replies: 66
Views: 22,902
Posted By rcgerber

Dang, was hoping they were closer to Proline...

Dang, was hoping they were closer to Proline M4/Jconcept black or maybe at least equal to a Jconcept green but more than a Proline M3.
Really want to try some but need a softer compound for where I...
12-29-2016, 02:15 PM
Replies: 66
Views: 22,902
Posted By rcgerber

Jason what's your soft compound compare to in...

Jason what's your soft compound compare to in another brands compound chart? IE a proline M4 or Jconcept green?
12-01-2016, 05:57 AM
Replies: 17
Views: 3,228
Posted By rcgerber

Unfortunately it doesn't look like that...

Unfortunately it doesn't look like that transmitter doesn't have endpoints. I don't recall these being very fast back in the day, but it's definitely not an inside car. There are two easy ways to...
11-25-2016, 08:04 AM
Replies: 300
Views: 46,142
Posted By rcgerber

Yep, there are 0deg, 3deg, 4deg, and 5deg caster...

Yep, there are 0deg, 3deg, 4deg, and 5deg caster blocks available.
I agree on the chassis as a tuning option for the V2 based lines. It would be a cool option for the new V3mm chassis, ie a...
11-21-2016, 06:38 AM
Replies: 15
Views: 3,348
Posted By rcgerber

Oh also looks like they check their facebook page...

Oh also looks like they check their facebook page so hit them up for any questions you might have.
11-21-2016, 06:33 AM
Replies: 15
Views: 3,348
Posted By rcgerber

Dc Hobbies 350 Old Oxford Rd, Covington, GA...

Dc Hobbies
350 Old Oxford Rd, Covington, GA 30014
It is right off I20 (You can see it from the highway).
10-10-2016, 02:27 PM
Replies: 282
Views: 49,000
Posted By rcgerber

I think it would work. I know of a guy that put a...

I think it would work. I know of a guy that put a v2 trans in his v3 fm (before the new MM car came out). So I have to assume it wouldn't be to hard to do it the other way. You would have to drill...
09-21-2016, 02:28 PM
Replies: 5,032
Views: 1,065,599
Posted By rcgerber

They can't do their own distribution. They have a...

They can't do their own distribution. They have a contract with Swift/Amain to be the exclusive US importer.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.