R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: Imbue
Showing results 1 to 25 of 460
Search took 0.11 seconds.
07-02-2017, 04:59 PM
Replies: 24
Views: 5,270
Posted By Imbue

OP, I would give a look in the Mugen thread, on...

OP, I would give a look in the Mugen thread, on Mugen/FP FB pages and the MBX7 Community page on FB as well. Since FP is synonymous with Mugen, the bulk of sales are to Mugen owners, which is where...
02-21-2017, 04:20 PM
Replies: 3
Views: 615
Posted By Imbue

7068 is "only" 35% stronger than 7075. In terms...

7068 is "only" 35% stronger than 7075. In terms of chassis parts, it's too marginal of a gain for 2.5x the material cost. It's more economical to leave on an extra 0.5mm of material, for example, to...
12-16-2016, 01:03 AM
Replies: 2
Views: 472
Posted By Imbue

For the Sirio, stick with Werks, Orion, Sirio,...

For the Sirio, stick with Werks, Orion, Sirio, Picco or Nova plugs, either #5 or #6 in either. Picco #6 probably being preferred.
10-17-2016, 02:12 PM
Replies: 9
Views: 1,421
Posted By Imbue

You should be able to simply delete the tensioner...

You should be able to simply delete the tensioner pulley all together. I had the same failure on the same box, and just rotated the motors on the mount to take up the slack in the belt.
08-03-2016, 12:08 PM
Replies: 87
Views: 20,658
Posted By Imbue

My apologies for the delay in updating this...

My apologies for the delay in updating this thread. We have released our V3 pistons, adding two additional hole configurations. They are available now. :)

...
07-03-2016, 11:08 AM
Replies: 87
Views: 20,658
Posted By Imbue

We'll have some news after the holiday weekend....

We'll have some news after the holiday weekend. Don't worry, it's a good thing. :nod:
09-14-2015, 05:02 PM
Replies: 841
Views: 166,120
Posted By Imbue

Got a chance to play around with the shocks this...

Got a chance to play around with the shocks this weekend. If you want a very smooth shock, you can replace the plastic spacer in the cartridge with 2 o-rings. So you have 4 o-rings, and then the...
06-10-2015, 04:26 AM
Replies: 3
Views: 380
Posted By Imbue

The 408 series has a fixed ackerman, it cannot be...

The 408 series has a fixed ackerman, it cannot be adjusted. You might (I use that reluctantly) be able to rig something up using the Losi ackerman bits.
05-20-2015, 08:16 AM
Replies: 841
Views: 166,120
Posted By Imbue

Since I can't be the only one who's driven up a...

Since I can't be the only one who's driven up a wall by the swaybar holders flexing, here's a quick (and a little dirty) solution to that problem. You'll need a 1.5mm drill bit and four M2x3mm...
04-19-2015, 11:38 AM
Replies: 87
Views: 20,658
Posted By Imbue

6x1.5 to 5x1.45 is a decently big swing. Were any...

6x1.5 to 5x1.45 is a decently big swing. Were any chassis setup changes made to compensate?


Just curious, how long did you run the pistons before the warm up? They require some break-in time...
03-09-2015, 11:25 AM
Replies: 6
Views: 448
Posted By Imbue

If using nylon, Weld-On 1701 is probably a...

If using nylon, Weld-On 1701 is probably a suitable alternative for limited usage.
03-09-2015, 11:16 AM
Replies: 6
Views: 448
Posted By Imbue

It's not a sealant at all. It's...

It's not a sealant at all. It's plastic/ultrasonic welded.
03-09-2015, 08:51 AM
Replies: 2
Views: 819
Posted By Imbue

Hondabond 4 will probably be the better option. I...

Hondabond 4 will probably be the better option. I don't believe HT flows as well as 4. Just make sure you have a jig or figure out a way to keep the crank at the correct angle while the liquid gasket...
02-28-2015, 06:42 PM
Replies: 42
Views: 5,151
Posted By Imbue

Thoughts are with the family. Dropped off a...

Thoughts are with the family. Dropped off a donation on PP, hopefully it can help the family through tough times.
02-18-2015, 03:31 PM
Replies: 124
Views: 23,249
Posted By Imbue

No. They are distributed by Amain (Swift...

No.

They are distributed by Amain (Swift Dist.) but they are not owned by Amain/Swift, like Protek.
01-26-2015, 05:27 PM
Replies: 249
Views: 50,668
Posted By Imbue

Because R/C isn't in as bad of a spot as may of...

Because R/C isn't in as bad of a spot as may of doom-and-gloomers think it's in.

Yes, it's not as great as it used to be, but its not all on the brink of collapse.
01-21-2015, 12:34 PM
Replies: 10
Views: 1,064
Posted By Imbue

Designing an engine that will run is rather easy....

Designing an engine that will run is rather easy. Just get any engine and reverse engineer it. The majority of today's .21 engines are all reverse-engineered off of each other and have become...
01-15-2015, 05:02 PM
Replies: 249
Views: 50,668
Posted By Imbue

SIC (which I believe is what you're referring to)...

SIC (which I believe is what you're referring to) is two weekends from this coming weekend, FWIW.
01-08-2015, 03:32 PM
Replies: 14
Views: 2,200
Posted By Imbue

Depending on how you look at it, there's actually...

Depending on how you look at it, there's actually two HARA editions.

2008 WC Edition (VZB Spec II)
http://rcspecial.com/news/wp-content/uploads/2008/10/os1710081.jpg

2010 Hara Edition (XZB...
01-02-2015, 10:00 PM
Replies: 118
Views: 41,396
Posted By Imbue

I tested a 2014 engine when we were interested in...

I tested a 2014 engine when we were interested in distributing them last year. They're great engines that run very well with a nice power band, and they should be priced really really well.
11-13-2014, 04:07 PM
Replies: 14
Views: 848
Posted By Imbue

I think some may have miss read this question....

I think some may have miss read this question. Aluminum cross shafts for the internal spider gears are fine. The Durango plastic ones are even better if they fit your brand (3.5mm shafts).
11-04-2014, 12:56 AM
Replies: 87
Views: 20,658
Posted By Imbue

Start around 35/30

Start around 35/30
11-04-2014, 12:49 AM
Replies: 87
Views: 20,658
Posted By Imbue

To help racers find setups that work with our...

To help racers find setups that work with our pistons, we're planning to add a setup sheet area on our site for easy reference. If you have a setup sheet you'd like to see on our site, please email...
10-29-2014, 09:50 PM
Replies: 87
Views: 20,658
Posted By Imbue

16mm Pistons are back in stock for those who have...

16mm Pistons are back in stock for those who have been waiting!



Wow, I can't believe I didn't catch your post. Very sorry about that.

I would start around 500cst F (AE 40wt), 425cst (AE...
10-27-2014, 09:49 AM
Replies: 87
Views: 20,658
Posted By Imbue

16mm version is correct for the MBX7R, 2.6mm...

16mm version is correct for the MBX7R, 2.6mm mounting hole.


Underway has/does/did.
http://www.rctech.net/forum/13487928-post37.html
Showing results 1 to 25 of 460
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.