Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: ThePanda
Showing results 1 to 25 of 500
Search took 6.52 seconds.
Forum: Rookie Zone
04-19-2018, 05:03 PM
Replies: 3
Views: 445
Posted By ThePanda

3 racing sakura zero s

3 racing sakura zero s
04-10-2018, 10:32 AM
Replies: 175
Views: 21,665
Posted By ThePanda

ahh, perhaps I will need to pick up this kit, I...

ahh, perhaps I will need to pick up this kit, I haven't built a tamiya tc in a while.
03-25-2018, 12:35 PM
Replies: 2
Views: 258
Posted By ThePanda

up

up
03-25-2018, 12:35 PM
Replies: 5
Views: 403
Posted By ThePanda

up

up
03-23-2018, 03:27 PM
03-23-2018, 03:23 PM
Forum: Rookie Zone
03-18-2018, 12:56 PM
Replies: 5
Views: 374
Posted By ThePanda

did you miss a cross pin somewhere in the...

did you miss a cross pin somewhere in the driveline?
03-18-2018, 12:53 PM
Replies: 8
Views: 383
Posted By ThePanda

Something nearly everyone has done. When I ran...

Something nearly everyone has done. When I ran straight bullets to the battery I used a bright red piece of heat shrink on the positive side of the lead and red nail polish on battery terminals. It...
03-18-2018, 12:47 PM
Replies: 1,794
Views: 475,445
Posted By ThePanda

on a track car A front spool is good for...

on a track car

A front spool is good for longer corners, as it tones down the front a little bit.
A one way is better on a very technical track. it allows the car to rotate very easily under...
03-18-2018, 12:40 PM
Replies: 12
Views: 488
Posted By ThePanda

The first thing that i would try would be a...

The first thing that i would try would be a throttle calibration.
02-01-2018, 10:45 AM
Replies: 9
Views: 539
Posted By ThePanda

up

up
01-31-2018, 07:00 PM
Replies: 7
Views: 330
Posted By ThePanda

you could scuff the plates with high grit...

you could scuff the plates with high grit sandpaper
01-31-2018, 06:58 PM
Replies: 9
Views: 539
Posted By ThePanda

up

up
01-30-2018, 05:48 PM
Replies: 7
Views: 942
Posted By ThePanda

their mistake for not looking close enough...

their mistake for not looking close enough...
01-30-2018, 11:53 AM
Replies: 9
Views: 539
Posted By ThePanda

uppupu

uppupu
01-29-2018, 03:27 PM
Replies: 9
Views: 539
Posted By ThePanda

up

up
01-28-2018, 04:41 PM
Replies: 10
Views: 615
Posted By ThePanda

have him give some evidence of problems. sounds...

have him give some evidence of problems. sounds like someone trying to get something for free.
01-27-2018, 02:12 PM
Replies: 9
Views: 539
Posted By ThePanda

269 up

269 up
01-26-2018, 01:39 PM
Replies: 9
Views: 539
Posted By ThePanda

up

up
01-25-2018, 12:21 PM
Replies: 9
Views: 539
Posted By ThePanda

up

up
01-23-2018, 10:10 AM
Replies: 9
Views: 539
Posted By ThePanda

OBO

OBO
01-22-2018, 02:16 PM
Replies: 31
Views: 1,620
Posted By ThePanda

a leather punch is best to get a hole with no...

a leather punch is best to get a hole with no sharp edges that can tear. a reamer usually won't be able to make a clean hole in a tire.
01-22-2018, 02:06 PM
Replies: 9
Views: 539
Posted By ThePanda

up

up
01-20-2018, 11:42 AM
Replies: 9
Views: 539
Posted By ThePanda

01-18-2018, 11:58 AM
Replies: 32
Views: 1,405
Posted By ThePanda

up

up
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service