Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: d16dcoe45
Showing results 1 to 25 of 500
Search took 0.18 seconds.
01-09-2018, 10:04 AM
Replies: 5,472
Views: 1,387,058
Posted By d16dcoe45

Right, but that shows the o-ring which...

Right, but that shows the o-ring which (obviously) can be installed any direction. We were wondering about the u-ring and which direction. As stated, I am going with the open side towards the fluid.
01-01-2018, 05:44 AM
Replies: 5,472
Views: 1,387,058
Posted By d16dcoe45

Imagine if the o-ring was hollow, like a tube and...

Imagine if the o-ring was hollow, like a tube and you cut it in half, that is a u-ring. All the diagrams I can find for at78 only show the o-ring, so I am not sure which way the open side of the...
12-31-2017, 11:46 AM
Replies: 5,472
Views: 1,387,058
Posted By d16dcoe45

Thanks Mike. Which way should the open part...

Thanks Mike.

Which way should the open part of the "U" face? Or is it of little importance?
12-31-2017, 06:35 AM
Replies: 5,472
Views: 1,387,058
Posted By d16dcoe45

Heading back to the track after a break this fall...

Heading back to the track after a break this fall and wanted to set up my a800xah with the latest options. Ordered At78 but ordered op152s (u ring) instead of op152 (o ring). Should I order the...
09-29-2017, 04:35 PM
Replies: 98
Views: 39,676
Posted By d16dcoe45

I know this is a month old but I had to put this...

I know this is a month old but I had to put this out there: TSR The One was the motor to have last season but the Monster Max Team Spec has the lowest resistance I have ever seen 17.5-17.6 on a 17.5...
Forum: Chat Lounge
09-12-2017, 03:18 PM
Replies: 223
Views: 25,527
Posted By d16dcoe45

Also, a regular bog standard 21.5 Monster Max is...

Also, a regular bog standard 21.5 Monster Max is 56.2 across the board. Last years 21.5 Monster was well above 60. These new motors are knocking on the door of illegality. My newest TSR One 17.5 is...
Forum: Chat Lounge
09-12-2017, 03:10 PM
Replies: 223
Views: 25,527
Posted By d16dcoe45

Well my new Team Spec Monster Max 17.5 shows...

Well my new Team Spec Monster Max 17.5 shows 35.2, 35.3, on my cheapish meter, but wouldn't you know it my "Team" rotor is 1581 Gauss A and 1611 B--with an asymmetry of 6! And a, b, c are at least 4...
06-17-2017, 01:10 PM
Replies: 34
Views: 9,790
Posted By d16dcoe45

Packs come off warm, not hot. And no the...

Packs come off warm, not hot. And no the temperature of the packs are not checked by the track. I am well aware of the ROAR rule of 1c, but frankly I can't think of a serious and competitive STOCK...
06-17-2017, 09:41 AM
Replies: 1,723
Views: 477,933
Posted By d16dcoe45

Gizmo GZ1 already has...

Gizmo GZ1 already has that:http://kentech.files.wordpress.com/2016/06/img_5725.jpg
06-17-2017, 09:12 AM
Replies: 4
Views: 698
Posted By d16dcoe45

I do it on every ESC I set up. I like 18g black...

I do it on every ESC I set up. I like 18g black silicone wire. Just be mindful of POS and NEG polarity as it matters.
06-17-2017, 07:19 AM
Replies: 34
Views: 9,790
Posted By d16dcoe45

I race stock 17.5 in a VERY competitive on road...

I race stock 17.5 in a VERY competitive on road carpet track and I have found personally that the slight HP advantage from big amp rates is worth it. I was charging at 40a and discharging at 40a...
06-01-2017, 04:02 AM
Replies: 1,162
Views: 305,358
Posted By d16dcoe45

Has anyone directly compared the 17.5 v16 to the...

Has anyone directly compared the 17.5 v16 to the older 17.5 v15? I was getting avg. resistance of @20.5 milliohms on v15 and on a large indoor carpet track it was good but not as quick as a TSR The...
Forum: Racing Forum
03-22-2017, 05:36 AM
Replies: 13
Views: 1,275
Posted By d16dcoe45

Smile What is the track size in feet? Looking...

What is the track size in feet?

Looking forward to attending!;)
03-05-2017, 03:03 PM
Replies: 10
Views: 2,810
Posted By d16dcoe45

All the manufacturers current short (20mm spring)...

All the manufacturers current short (20mm spring) shocks have an ID of 11.2mm. I would wager a guess that they are 11.5mm with a slight chance of being 12.0mm ID.

Would love to know for sure...
12-31-2016, 08:38 AM
Replies: 4,583
Views: 968,418
Posted By d16dcoe45

the pins are anodized, polishing wont have much...

the pins are anodized, polishing wont have much of an effect. Even if they were raw aluminum or steel, polishing cross pins is getting to the point of ridiculousness! And i do quite a few...
12-23-2016, 07:33 AM
Replies: 8
Views: 3,575
Posted By d16dcoe45

yes, u physically unsolder the sensors on the...

yes, u physically unsolder the sensors on the sensor board and move them little by little to the correct positions--and of course permanently solder them back. Its a trial and error process but...
12-23-2016, 04:17 AM
Replies: 12
Views: 4,183
Posted By d16dcoe45

I actually thought the stock steering tension on...

I actually thought the stock steering tension on the M12 felt LESS connected so I installed the soft spring they supply and adjusted it down--I personally much prefer soft steering and throttle...
12-22-2016, 01:02 PM
Replies: 12
Views: 4,183
Posted By d16dcoe45

If your main requirement for a new radio is to...

If your main requirement for a new radio is to feel as connected as possible and to give you the greatest chance of winning or improving your racing I think its OVERWHELMINGLY obvious that there us...
12-12-2016, 06:00 AM
Replies: 114
Views: 22,335
Posted By d16dcoe45

Awesome event

Had a fantastic time at Stock Wars 2016.

Thanks to Donny for the amazing facility, Robbie Dodge for running a great event,Alex V for his tireless dedication to the hobby and entertaining color...
11-18-2016, 03:18 PM
Replies: 18
Views: 3,295
Posted By d16dcoe45

that is tough to answer because each can is built...

that is tough to answer because each can is built differently and you are only measuring the surface temp of the can when the stator windings are much higher! I have seen guys comfortable at 180 F...
11-18-2016, 07:45 AM
Replies: 18
Views: 3,295
Posted By d16dcoe45

I have found a no load draw between 6 and 7 amps...

I have found a no load draw between 6 and 7 amps is a good place to start. Every motor is a little different but it seems to range from @ 46 to 53 actual degrees for the above amps.

Gear to lap...
08-20-2016, 06:54 AM
Replies: 304
Views: 29,792
Posted By d16dcoe45

i havent been down to jackson since summer of '14...

i havent been down to jackson since summer of '14 and would love to get the last 2 races in before outdoor season is over.

Is it only 17.5 or is there a mod class too?
11-05-2015, 04:15 AM
Replies: 8,894
Views: 1,624,656
Posted By d16dcoe45

I wonder if its an original worlds from 99-2000...

I wonder if its an original worlds from 99-2000 or the reissue from 05-06? Either way absolute LEGEND and future collectible.
11-05-2015, 01:42 AM
Replies: 4,765
Views: 1,074,549
Posted By d16dcoe45

pre-order is up on Horizon!! Just preordered the...

pre-order is up on Horizon!! Just preordered the kit, chassis sheets and the alloy NORMAL nut style front axles.
Hope "early Dec" is accurate because this car looks amazing. More traditional 3 gear...
08-29-2015, 11:27 AM
Replies: 8,894
Views: 1,624,656
Posted By d16dcoe45

shorty here

Just ordered the shorty off Horizon but won't have it till next Friday.

Anyone have one and tried it?
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.