R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: AGNO
Showing results 1 to 25 of 500
Search took 0.16 seconds.
04-09-2014, 11:58 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

Also great Tamiya with 3Racing alu arm, I use it...

Also great Tamiya with 3Racing alu arm, I use it on my other TCXX.
Some drivers have had centering problems with this servo saver, personally, I not have any problems, work well.

You must choose...
04-08-2014, 01:50 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

The servo saver TCXX is great, the best on the...

The servo saver TCXX is great, the best on the market, precise, strong and durable, is composed of graphite.

The only alternative is to remove the servo saver and use a direct linkage, but the...
04-07-2014, 02:37 PM
Replies: 2,121
Views: 357,360
Posted By AGNO

I did several tests on asphalt, it works very...

I did several tests on asphalt, it works very well on this surface.
same impressions, very predictable and consistent handling.

I have not had the need to change position to the dampers, use the...
03-28-2014, 03:15 PM
Replies: 2,121
Views: 357,360
Posted By AGNO

Is an modified Jet motor support ;)

Is an modified Jet motor support ;)
03-28-2014, 06:02 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

Ergal vs carbon fiber. Ready for test! :) ...

Ergal vs carbon fiber.

Ready for test! :)

http://i62.tinypic.com/zin6u8.jpg
01-30-2014, 10:52 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

I think the difference is in the position of the...

I think the difference is in the position of the motor, positioned higher.
12-15-2013, 04:18 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

Less aggressive, good for open track But if...

Less aggressive, good for open track

But if you add even more toe-out, increases steering in tight and slow turns
12-15-2013, 04:13 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

With the sweep front arms( FF 1,5/FR 0) you...

With the sweep front arms( FF 1,5/FR 0) you have a car aggressive corner entry and lack mid corner

To increase the stability it is preferable to reduce the swep combining pivot FF 1,5 and FR 1...
12-11-2013, 03:27 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

+1 ;)

+1 ;)
12-11-2013, 03:21 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

The central post already existed in the old TCX,...

The central post already existed in the old TCX, long time before BD7...

Works fine even if it touches the central support, much better, there are more options for stiffening (same Tamy 418)
...
10-18-2013, 02:29 PM
Replies: 2,121
Views: 357,360
Posted By AGNO

Thanks for the reply ;)

Thanks for the reply ;)
10-16-2013, 02:42 PM
Replies: 2,121
Views: 357,360
Posted By AGNO

Hello Hiro, there are no news regarding the new...

Hello Hiro, there are no news regarding the new option ...?
10-16-2013, 02:40 PM
Replies: 2,121
Views: 357,360
Posted By AGNO

If you are interested, I have one for 17.5 and...

If you are interested, I have one for 17.5 and 13.5 blinky.
07-31-2013, 02:10 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

My TCX top deck prototype has improved the...

My TCX top deck prototype has improved the overall flex, the reactions of car are slightly less quickly, but driving is more constant and consistent, the tests are made with 13.5 blinky.


Soon I...
07-31-2013, 01:09 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

Andy's car ETS round 5 ;) The top deck of...

Andy's car ETS round 5 ;)

The top deck of Andy is a prototype, is not yet available :(

1095932
07-28-2013, 04:37 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

I also tested the kit CSO lower shock and towers,...

I also tested the kit CSO lower shock and towers, and work very well.

I used this setting

Front and rear 350 cps oil and 4 x 1,1mm piston

Front Xray spring 2.7

Rear std CSO sping 2.5
07-28-2013, 04:14 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

I did some tests using a modified TCX top deck, I...

I did some tests using a modified TCX top deck, I did not use shims, the central shaft remains in place and there a good flex.

You can change the flex simply re-using two screws.

Post some...
07-11-2013, 02:45 AM
Replies: 1,316
Views: 308,858
Posted By AGNO

My old HPI PRO4 is still very fast :nod: ...

My old HPI PRO4 is still very fast :nod:

http://i41.tinypic.com/vobvoy.jpg
05-31-2013, 10:10 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

Work very well, I use 6 x 1.1 with oil 700/800,...

Work very well, I use 6 x 1.1 with oil 700/800, they work fine on asphalt in all grip conditions, do not use vent hole.

The diameter of these pistons is very accurate, check the smoothness in the...
05-27-2013, 08:02 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

Use 46mm spec-R DCJ V.2 , they are awesome, very...

Use 46mm spec-R DCJ V.2 , they are awesome, very smooth and strong, for to be use however require the use of spool outdrive TCX, steel or POM (#61087-#68769-#68770)
05-06-2013, 01:39 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

News from Smokem ;) Chassis no cut 2,25mm ...

News from Smokem ;)

Chassis no cut 2,25mm

1064756

Servo mount (use only with Smokem chassis)

1064757
05-06-2013, 01:35 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

The standard TCXX chassis works very well even in...

The standard TCXX chassis works very well even in case of low grip, it is sufficient to use the top deck 2mm, with high grip and treated surface works well with standard top deck 2,5mm.
04-12-2013, 02:31 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

Yes, with low roll center we have more roll, but...

Yes, with low roll center we have more roll, but the handling is more predictable.
High roll center, on high bite carpet, makes driving very nervous and unpredictable the roll over.

At least, it...
04-11-2013, 01:39 AM
Replies: 2,121
Views: 357,360
Posted By AGNO

Yes, I Use on high grip carpet surface, work very...

Yes, I Use on high grip carpet surface, work very well.
03-21-2013, 05:40 AM
Replies: 12,554
Views: 1,765,717
Posted By AGNO

Endbell with timing adjust,for Hobbywing motors.

Endbell with timing adjust,for Hobbywing motors, +15 deg, more RPM (+10.000), more power, best use for NO timing class :nod:

1046314
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.