R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Community
Wiki Posts
Search
Search: Posts Made By: liquiddog
Showing results 1 to 10 of 10
Search took 0.02 seconds.
01-17-2010, 07:17 AM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

After reading much on here, I tried out v203 with...

After reading much on here, I tried out v203 with a Ballistic 17.5 in TC. I ran a 5.4 FDR, 50 boost, 10 turbo, ramp 2, start 4000-ish, end 12500. I had the motor set to -3 notches (furthest...
01-12-2010, 06:18 AM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

Thanks for that info. I've read back at least 40...

Thanks for that info. I've read back at least 40 posts and have been following this thread daily just to try and figure out how many RPMs a 17.5 puts out, and how far back I should set it back to...
01-07-2010, 05:47 AM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

How many people run a fan on their Tekins? Is...

How many people run a fan on their Tekins? Is there an aftermarket kit or is it even necessary? I'm sure it's been asked before, but it must be more than 50 pages back, and I'm assuming the new...
01-05-2010, 06:40 PM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

Thanks for the superb doc. It answers all of my...

Thanks for the superb doc. It answers all of my questions including the question I had about the Ballistic motor timing. Huge wealth of info here.
01-05-2010, 06:02 AM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

Is this the correct number? A Tekin motor set at...

Is this the correct number? A Tekin motor set at the "0" mark is at 15 degrees actual timing? If so, then based on previous setups posted a Ballistic would be set at the leftmost mark which would...
01-04-2010, 03:13 PM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

The Novak site says N is 30 degrees. Is that the...

The Novak site says N is 30 degrees. Is that the same as 0 Deg on a Tekin motor? I only ask because it says in a Novak document that timing numbers from different motor manufacturers can mean...
01-04-2010, 12:13 PM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

What is a good setup for an RS with a Ballistic...

What is a good setup for an RS with a Ballistic 17.5 for a TC? End bell timing setting? Hotwire settings?
01-04-2010, 06:13 AM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

I just got a RS Pro along with a Hakko 936 ESD...

I just got a RS Pro along with a Hakko 936 ESD soldering station. I'm also looking for a RS non-Pro locally so I'm going to have two ESCs to solder. I picked up a 5mm angled chisel tip and 60...
12-11-2009, 09:29 AM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

I definitely want sensored so it looks like the...

I definitely want sensored so it looks like the RX8 is out. I knew there must be some difference. I'll probably stick with the RS Pro because it may one day end up on a off-road 4WD if Tekin comes...
12-11-2009, 05:22 AM
Replies: 23,359
Views: 2,659,605
Posted By liquiddog

I've been on the fence for a long time about...

I've been on the fence for a long time about which ESC to buy. I'm finally ready to make the plunge to brushless so I'm forced to make the choice. I decided on Tekin because I don't want to have to...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.