R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Community
Wiki Posts
Search
Search: Posts Made By: ShtLuck
Showing results 1 to 22 of 22
Search took 0.01 seconds.
05-14-2012, 08:36 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

All u need is The kit and a nitro roller

All u need is The kit and a nitro roller
04-08-2012, 07:15 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

Not sure... I won't run tekin, I have had no...

Not sure...
I won't run tekin, I have had no luck with their product over the last few years.
04-08-2012, 07:05 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

I I believe I am going to have to swap motors. ...

I I believe I am going to have to swap motors.
The car is great on track, just sucks that I have buy another motor again.
04-08-2012, 04:19 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

Because joy on doesn't have the same car as I do.

Because joy on doesn't have the same car as I do.
04-08-2012, 03:22 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

I run the 150amp that the Orion esc is based on.

I run the 150amp that the Orion esc is based on.
04-08-2012, 12:40 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

Currently running a hobbywing after my 3rd failed...

Currently running a hobbywing after my 3rd failed mamba pro and 4 failed rx8's... Mamba had bad sensor boards and the tekins appeared to hate electricity.
04-08-2012, 12:35 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

Currently running a hobbywing after my 3rd failed...

Currently running a hobbywing after my 3rd failed mamba pro and 4 failed rx8's... Mamba had bad sensor boards and the tekins appeared to hate electricity.
04-08-2012, 08:42 AM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

Can't flip the diffs, the rear is offset much...

Can't flip the diffs, the rear is offset much like a Losi.
04-08-2012, 08:08 AM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

Well to be honest I had no choice but to run it...

Well to be honest I had no choice but to run it yesterday as it was the first roar regional race of the series.
Car handled amazing, very impressed with the Tekno kit, however I did try to run the...
04-07-2012, 06:34 AM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

Swell I just figured out I can only run it non...

Swell I just figured out I can only run it non sensored. Defeats the purpose ....
It's officially for sale now.:flaming:
04-06-2012, 07:25 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

They list it as 0, however their 0 and tekins 0...

They list it as 0, however their 0 and tekins 0 varies as it does across the board.
For example Lrp 10th motors are buil with 30 degrees, tekin 18ish etc....
04-06-2012, 07:23 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

To be honest the hyper 9's aren't being run much...

To be honest the hyper 9's aren't being run much in my area, never looked at one.:lol:

As for the built in timing measurement I haven't gotten a solid answer yet. The TP motors aren't like most...
04-06-2012, 07:14 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

I run a very linear throttle profile. I add...

I run a very linear throttle profile. I add timing on the can to take some punch out the motor, it makes the motors very smooth through out the rpm range. Also I can run a smaller pinion and still be...
04-06-2012, 06:04 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

I run the new zr3 8 1900kv

I run the new zr3 8 1900kv
04-06-2012, 05:13 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

I run thunderpower motors. I can reverse the...

I run thunderpower motors.
I can reverse the esc but that seems counter productive since I have spent so much time on esc and motor set ups just to toss that out the window now and start winging it...
04-06-2012, 04:18 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

also on a side note: typical sensored motor is...

also on a side note:
typical sensored motor is built with advanced timing built in them wether or not the endbell says 0. some up to 30 degrees.
if you spin the motor the other way you are now...
04-06-2012, 04:14 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

actually i dont run tekin or novak, and i run...

actually i dont run tekin or novak, and i run timing on my setups so i do have something to complain about....
04-06-2012, 04:11 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

the jq v4 mounts the motor in the opposite...

the jq v4 mounts the motor in the opposite direction as all the other kits they make. thus the issue.
it needs to be on the battery side of the driveline to spin the correct direction for the motor.
04-06-2012, 04:04 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

you can reverse the direction but you are now...

you can reverse the direction but you are now running non sensored because the timing ring is built to run the other direction.
04-06-2012, 03:55 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

so i bought a jq v4 conversion.... I am very...

so i bought a jq v4 conversion....
I am very confused why tekno would build a kit that cant be used with sensored systems. I am now sitting here with a kit i can not use or electronics i can not...
04-03-2012, 08:51 AM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

Hey busted What gearing are u running on that...

Hey busted
What gearing are u running on that setup.
04-02-2012, 04:45 PM
Replies: 10,255
Views: 1,279,385
Posted By ShtLuck

I was wondering if anyone has a good baseline...

I was wondering if anyone has a good baseline outdoor setup for a tekno'd JQ.
Showing results 1 to 22 of 22


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.