R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
Search: Posts Made By: Ferret
Showing results 1 to 11 of 11
Search took 0.00 seconds.
Forum: Electric Off-Road
06-17-2011, 12:56 PM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

How can you get 30* kick?

How can you get 30* kick?
Forum: Electric Off-Road
05-30-2011, 07:25 AM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

From my experience, the problem with LP servos is...

From my experience, the problem with LP servos is not that they lack strength, but that they tend to have a high peak power draw (because they use a shorter motor), which can overwhelm the BEC and...
Forum: Electric Off-Road
05-03-2011, 04:48 AM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

I had some problems fitting the stock horn to the...

I had some problems fitting the stock horn to the servo (Savox 1251) and ended up using a XXX cr horn.

I had to dremel some material off it to create clearance for the link. I positioned the servo...
Forum: Electric Off-Road
05-01-2011, 03:30 PM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

Since I like my setups with a lot of down travel,...

Since I like my setups with a lot of down travel, I'm trying to find out if someone else has a lot of down travel without the spindles catching before I try to reinvent the wheel.

I don't want to...
Forum: Electric Off-Road
05-01-2011, 12:45 PM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

They are screwed until the thread is no longer...

They are screwed until the thread is no longer visible, it may be possible to give them another turn or so.

Is the car without the limiters running 5 deg caster blocks and the car with limiters...
Forum: Electric Off-Road
05-01-2011, 11:09 AM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

The stud isn't poking it's the spindle itself...

The stud isn't poking it's the spindle itself that's touching and the spacers are according to the manual and setup sheet, 0.5 mm above the spindle and 1.5 mm below.

Are you running without...
Forum: Electric Off-Road
05-01-2011, 10:52 AM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

I would try to borrow a set of wheels from one of...

I would try to borrow a set of wheels from one of the other guys running the same setup and do a few laps. If the the problem disappears, then it could be the close cells (assuming everyone is also...
Forum: Electric Off-Road
05-01-2011, 09:06 AM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

Fouling spindle.

When the suspension is at full droop and I try to apply full steering lock, the inside spindle (the one on the same side as the steering direction) touches the wishbone where the ball stud threads...
Forum: Electric Off-Road
04-28-2011, 04:47 AM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

Caster

Regarding all the caster discussions:

Keep in mind that the caster is the total inclination of the king pins. Foe example, you can get 30 deg. caster in two ways, when you use the 20 deg. shim...
Forum: Electric Off-Road
04-14-2011, 12:47 PM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

My 22 yet still hasn't arrived yet, but someone...

My 22 yet still hasn't arrived yet, but someone here wrote that the front hex is the same size as the 4WD front hex (which is 3/8", 9.6 mm).

Avner.
Forum: Electric Off-Road
12-02-2010, 12:18 PM
Replies: 21,236
Views: 3,151,860
Posted By Ferret

Off topic, but what is the "large nut mod"? ...

Off topic, but what is the "large nut mod"?

Avner.
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.