R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
 
Page 1 of 3
1
2
3
Search: Posts Made By: Roelof
Showing results 1 to 25 of 62
Search took 0.00 seconds.
Forum: Nitro On-Road
10-22-2013, 02:33 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

Serpent has a setup book for their 966/960

Serpent has a setup book for their 966/960
Forum: Nitro On-Road
05-27-2013, 10:02 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

When the shoe wears the gap will be larger and so...

When the shoe wears the gap will be larger and so more rpm is needed to engage and it will create moe slip.

Most of the time it is safe to keep the gap at 0.7mm. with a new shoe set it to 0.6.
If...
Forum: Nitro On-Road
03-05-2011, 02:26 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

That is the rear damper set from the MRX-4R ,...

That is the rear damper set from the MRX-4R , that one has the long dampers.

But realy, it does not give an improvement.
Forum: Nitro On-Road
12-03-2010, 10:20 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

But not the width of the wheels and so the...

But not the width of the wheels and so the distance between both uprights.

My gues is that it would fit but there is a chance that some small modifications are needed
Forum: Nitro On-Road
06-17-2010, 10:49 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

I just use a 10cm servo extension cable which I...

I just use a 10cm servo extension cable which I leave in the receiver and the oter end I use to connect and disconnect the battery. In the past I have used switches and I only have dad experiences...
Forum: Nitro On-Road
06-06-2010, 10:17 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

Be sure the tensioner is not set to tight!

Be sure the tensioner is not set to tight!
Forum: Nitro On-Road
06-06-2010, 02:46 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

Just run the car, all will become loose.

Just run the car, all will become loose.
Forum: Nitro On-Road
06-05-2010, 12:28 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

Clean the belt! For sure the side belt does...

Clean the belt!
For sure the side belt does pick up a lot of rubber, just use a towel, put some fuel on it, push it on the belt on the side pulley and turn the wheels arround.

Before the race I...
Forum: Nitro On-Road
04-27-2010, 06:50 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

The battery tray is different, the 4X has a screw...

The battery tray is different, the 4X has a screw comming out into the short middle schaft mount.
The 4X excentrics in front and rear for tensioning the belt has 2 notches, it can be turned 180...
Forum: Nitro On-Road
04-23-2010, 11:40 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

And if you take a search on Ebay you will always...

And if you take a search on Ebay you will always find an older car you can strip for the parts.
Forum: Nitro On-Road
03-27-2010, 12:06 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

In a far past on steel brakepads.... It works but...

In a far past on steel brakepads.... It works but you have to learn it. When heating up it will give more brakepower so when hitting the brake in the beginning there is not mucht and a moment later...
Forum: Nitro On-Road
03-03-2010, 02:44 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

I wonder if people can feel the difference in the...

I wonder if people can feel the difference in the old MRX4 arm and the 4R/X arms with only a 1 or 2mm moved shockposition.

I have plenty of old MRX4 parts and when needed I just use them without...
Forum: Nitro On-Road
02-13-2010, 06:16 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

The BL452 is with .14 sec slow. The 451 is with...

The BL452 is with .14 sec slow. The 451 is with 0.1 sec the right choice for a good response and the 10kg is enough, even for an 1/8 scale car.

Currently I run Savox 1257 servo's, they are also...
Forum: Nitro On-Road
02-13-2010, 03:06 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

For serious racing for sure on the steer it is...

For serious racing for sure on the steer it is too slow. I went from 0.1 sec to 0.07 sec servo's and I noticed the gain in speed in a better stering response and better positioning of the car.
On...
Forum: Nitro On-Road
02-01-2010, 12:14 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

I think the squat setting is to much on the rear...

I think the squat setting is to much on the rear although a friend did play with it on his HPI R40 and did get more out of the car. Regarding the front upper wishbone you could see Salven running it...
Forum: Nitro On-Road
01-18-2010, 01:57 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

The 45/20 is almost never used unless you are...

The 45/20 is almost never used unless you are running an engine with a lot of torque and low rpm (as with a long manifold).

Most people here are running the 16 pinion or even 15 combined with 49...
Forum: Nitro On-Road
01-09-2010, 09:38 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

[QUOTE=epowr_Racing;6828489] Robert...

[QUOTE=epowr_Racing;6828489]

Robert Pietch....

He was running Velox uprights and steerblocks on his Mugen during the Worlds. I have heard Mugen has its own blocks with excentric inserts.
Forum: Nitro On-Road
12-13-2009, 11:58 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

Most R drivers are just using the new rear upper...

Most R drivers are just using the new rear upper arms with their mountings and the short rear shocks with the X shocktower. If you have these parts from the old MRX4 it will do almost the same.
...
Forum: Nitro On-Road
12-01-2009, 11:26 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

Yes it does. You can lower that by cutting off...

Yes it does. You can lower that by cutting off the long end tip and drill some holes in the rest of it.
Forum: Nitro On-Road
11-01-2009, 11:46 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

The new 35-plus-21 has a purple head and is still...

The new 35-plus-21 has a purple head and is still using a 5mm crankpin. The Collari versions (except the latest Lostallo edition) run a smaller crankpin which will give some issues.
Forum: Nitro On-Road
10-14-2009, 03:46 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

This is not used as a tensioner but only to keep...

This is not used as a tensioner but only to keep the belt on his place.
If you place the bearings not that low then it is only enough to grind an edge on the saver.
Lowerig the saver can be done...
Forum: Nitro On-Road
10-13-2009, 02:23 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

With my modification you can run several races...

With my modification you can run several races without any problem, even the plastic pulley stays in shape.
Forum: Nitro On-Road
10-12-2009, 11:29 PM
Replies: 1,676
Views: 219,690
Posted By Roelof

Take a look here: ...

Take a look here:
http://www.rctech.net/forum/nitro-road/283399-no-more-stripping-frontbelts.html
Forum: Nitro On-Road
10-11-2009, 01:50 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

The wheel axle will always stay in the center of...

The wheel axle will always stay in the center of the wheel and so on the same hight.....
I believe you can set the axle also forward/backward changing the wgeelbase, that will do more.
Forum: Nitro On-Road
10-02-2009, 06:05 AM
Replies: 1,676
Views: 219,690
Posted By Roelof

The tires which come with the Edam Spirit 1/8 RTR...

The tires which come with the Edam Spirit 1/8 RTR are rubber tires but on Serpent rim.
Showing results 1 to 25 of 62
 
Page 1 of 3
1
2
3


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.