R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
Search: Posts Made By: Antimullet
Showing results 1 to 15 of 15
Search took 0.01 seconds.
Forum: Electric Off-Road
12-31-2021, 07:57 PM
Replies: 1,897
Views: 646,826
Posted By Antimullet

Sanwa Receiver, no antenna. Even the old ones...

Sanwa Receiver, no antenna. Even the old ones with antenna I would just wrap and keep with receiver, and not route the wire anywhere. Never had an issue, with the spread spectrum stuff.
Not the same...
Forum: Electric Off-Road
02-22-2021, 06:55 PM
Replies: 1,897
Views: 646,826
Posted By Antimullet

Is this some kind of hippy love in session? I知...

Is this some kind of hippy love in session? I知 not bashing anything I知 just telling it how it is. The 6240 is a crap servo and will fail. There is no place for it in a wheeler driven hard. The...
Forum: Electric Off-Road
01-27-2021, 04:37 PM
Replies: 1,897
Views: 646,826
Posted By Antimullet

The A-Blocks suck, they are too thin and I've...

The A-Blocks suck, they are too thin and I've broke multiple. Barely a lateral hit and the pills will spit out the side of the A-Blocks because someone at Losi doesn't understand wall thickness and...
Forum: Electric Off-Road
01-27-2021, 04:32 PM
Replies: 1,897
Views: 646,826
Posted By Antimullet

3.0 shaft setup sucks unless you like to bottom...

3.0 shaft setup sucks unless you like to bottom out and run high weight oil. Both my wheeler and 2wd work great with the 3.5. This 3.0m stuff is garbage for someone that likes a car with dampening.
Forum: Electric Off-Road
12-20-2020, 08:21 PM
Replies: 1,897
Views: 646,826
Posted By Antimullet

no sorry, but they were just the exotek carbon...

no sorry, but they were just the exotek carbon batter straps. I just shimmed them and used existing screw holes on the car to get them to work.
The tabs aren稚 as wide as I want so I値l be making...
Forum: Electric Off-Road
12-20-2020, 08:19 PM
Replies: 1,897
Views: 646,826
Posted By Antimullet

the bolt spacing on the can is a little wider....

the bolt spacing on the can is a little wider. You can file the motor mount hole a touch and it値l go it.
Forum: Electric Off-Road
12-14-2020, 05:47 PM
Replies: 1,897
Views: 646,826
Posted By Antimullet

I got rid of the rubber oring system. I had some...

I got rid of the rubber oring system. I had some leftover b6.1 battery tabs from Exotek and used them. Ditto for my 5.0 DC Elite.
Forum: Electric Off-Road
10-06-2020, 05:49 AM
Replies: 1,897
Views: 646,826
Posted By Antimullet

I run the stiffezels.

I run the stiffezels.
Forum: Electric Off-Road
10-06-2020, 05:49 AM
Replies: 1,897
Views: 646,826
Posted By Antimullet

Correct but up to a point. Too much and it...

Correct but up to a point. Too much and it becomes inconsistent. I like the way it feels with the added stiffeners I rigged up. Makes it more consistent for me but allows a bit of flex still....
Forum: Electric Off-Road
10-04-2020, 05:11 PM
Replies: 1,897
Views: 646,826
Posted By Antimullet

I致e got my own carbon so I値l make my own. Also...

I致e got my own carbon so I値l make my own. Also going to increase the thickness of the lower carbon stiffeners on the chassis itself.

Will the X-rays even fit?
Forum: Electric Off-Road
10-04-2020, 06:41 AM
Replies: 1,897
Views: 646,826
Posted By Antimullet

Flex testing.

I noticed my car had a lot of flex so I tested some mock up bracing.
For me I like a neutral car and the elimination of some of the flex definitely helped with
that and for me made it more...
Forum: Electric Off-Road
09-10-2020, 07:42 PM
Replies: 1,897
Views: 646,826
Posted By Antimullet

What is?

What is?
Forum: Electric Off-Road
09-09-2020, 12:57 AM
Replies: 1,897
Views: 646,826
Posted By Antimullet

same here feels way too underdamped and slaps...

same here feels way too underdamped and slaps like crazy.
Forum: Electric Off-Road
09-08-2020, 06:49 AM
Replies: 1,897
Views: 646,826
Posted By Antimullet

Anyone know parts needed to go to the 3.5mm shock...

Anyone know parts needed to go to the 3.5mm shock shafts? I don't like the stock 3mm and piston package at all. Way too little dampening for me and a lot of chassis slap.
Forum: Electric Off-Road
08-31-2020, 07:41 AM
Replies: 1,897
Views: 646,826
Posted By Antimullet

Pull grip out of the front. Several ways to do...

Pull grip out of the front. Several ways to do it. Less grippier tires first, Harder springs, roll centers, less camber, ball stud height adjustment, axle height adjustment, etc.

no sways I...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.