R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Community
Wiki Posts
Search
Search: Posts Made By: panic-rev
Showing results 1 to 19 of 19
Search took 0.00 seconds.
11-25-2011, 10:50 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

I doubt it was the sleep. This car I...

I doubt it was the sleep.

This car I thought was a nightmare build. Don't hate.... just talking about build only. The car is quality and looks to drive pretty sweet. But I was very un-impressed...
11-16-2011, 02:34 AM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

Hey fulzz, I can only assume the threads on the...

Hey fulzz, I can only assume the threads on the tc5 are the same diameter as the stock 210's? I just ask cuz I thought the 210 was kind of a bigger size. So if you have ALREADY put the 210 studs in,...
11-15-2011, 07:58 AM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

Where were they poppoing off from? Random places?...

Where were they poppoing off from? Random places?
Did you have them lined up properly?
Stiffer CF Steering link?

We believe you on the good driver part, so yeh, it sounds like you feel...
11-15-2011, 07:33 AM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

So along with this post too.... So...

So along with this post too....



So could it be that it's just the rear alignment then? and maybe the front steering ones are caused by a flexy steering link (discussed a few pages back)?
...
11-15-2011, 12:45 AM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

A picture is worth a 1000 words :D.

A picture is worth a 1000 words :D.
11-14-2011, 07:17 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

I'm a little confused by this post. So it's been...

I'm a little confused by this post. So it's been discussed that there is a problem with ballcups, and you're saying to keep the stock ballstuds because they're stronger, but the solution is just buy...
11-14-2011, 07:05 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

Since we're on the subject..... So the...

Since we're on the subject.....

So the Durango Ballstuds are bigger and beefier than your typical B4 ones? I havn't seen them in person.

Now what's the actual weak point.....the ballcups?...
11-14-2011, 03:27 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

True. It makes sense to most I'm sure. There are...

True. It makes sense to most I'm sure. There are too many what ifs though to open a debate on theoretical partical physics, so lets leave it shut and hope we don't break our cars which there are no...
11-14-2011, 02:21 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

I don't have mine, so good heads up if this piece...

I don't have mine, so good heads up if this piece looks a little suspect.



But your servo could be next in line. Sketchy. I'm thinking plastic is the play.

As far as "something's gotta...
11-14-2011, 12:43 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

Are these the same piece? B4 Ackerman = 210...

Are these the same piece? B4 Ackerman = 210 Steering Plate?

Wow....didn't realize there was no servo saver on the 210. The B4 essentially doesn't have one either since it sux and they all...
11-14-2011, 09:20 AM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

Shock towers and steering plate? Weak points? I...

Shock towers and steering plate? Weak points? I didn't hear.

Shock towers make obvious sense. I did order some extra towers just cuz they were exposed and looked like they could take the brunt of...
11-14-2011, 09:14 AM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

Good read Johnny5.

Good read Johnny5.
11-13-2011, 11:08 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

What is stock spur? Anyone running 8.5 or close?...

What is stock spur? Anyone running 8.5 or close? What pinion matches up well? Thanks.
11-13-2011, 10:43 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

From Hopsing's and Bman's posts above, I am going...

From Hopsing's and Bman's posts above, I am going to stick with the stock 6 hole and probably throw in some AE 35/30 to start, see where it takes me. Thanks for the input.

I wonder if the nature...
11-13-2011, 06:35 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

PS..... Is there a drill bit size that...

PS.....

Is there a drill bit size that equates to 1.3 or 1.2? Or is that the size? I've never drilled my own from scratch, just made bigger to existing. Just wondering what the actual bit is....
11-13-2011, 06:27 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

Are the 4 hole 1.2/1.3 pistons something that...

Are the 4 hole 1.2/1.3 pistons something that comes stock with kit? I know a bunch are included. Or did you drill the blank ones that come with it?

Do you all find it interesting that the car...
11-13-2011, 11:11 AM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

If anyone puts in an sc10 gear dif, would you...

If anyone puts in an sc10 gear dif, would you care to post pix or tell how many shims on each side, what kinda shims too. SC10 gear difs are pretty abundent and cheap.

Ill wear out my first ball...
11-12-2011, 11:30 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

I was getting all excited that the sc10 dif fit....

I was getting all excited that the sc10 dif fit. But moving side to side? Yeh, kind of a big deal. Not sure if that's what you meant. If it fits, like perfect, fill us in.
11-12-2011, 01:38 PM
Replies: 19,920
Views: 2,752,093
Posted By panic-rev

Amain doesn't show A-arms, does anybody have a...

Amain doesn't show A-arms, does anybody have a good online place they get Durango parts from? Thanks.
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.