R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Community
Wiki Posts
Search
Search: Posts Made By: sstumpf
Showing results 1 to 22 of 22
Search took 0.00 seconds.
02-06-2011, 07:24 PM
Replies: 41
Views: 12,020
Posted By sstumpf

well i think it is the rotor is just loose...

well i think it is the rotor is just loose because it does stop turning when i hit the breaks somtimes and i dont think it is because it has been overheated because sometims right when i turn it on...
02-06-2011, 05:14 PM
Replies: 41
Views: 12,020
Posted By sstumpf

ok i will check the magnet tomorrow also i did...

ok i will check the magnet tomorrow also i did notice that when the motor is fully assembled and in the truck that the shaft can be moved back and forth like in and out of the motor is cant move much...
02-06-2011, 10:45 AM
Replies: 41
Views: 12,020
Posted By sstumpf

well i got it taken apart without bending the...

well i got it taken apart without bending the shaft. and everything is fine in there nothing is broke and is all pretty clean. what could it be now
02-06-2011, 08:38 AM
Replies: 41
Views: 12,020
Posted By sstumpf

come on i really need some help on this

come on i really need some help on this
02-06-2011, 08:10 AM
Replies: 41
Views: 12,020
Posted By sstumpf

any ideas

any ideas
02-06-2011, 07:41 AM
Replies: 41
Views: 12,020
Posted By sstumpf

what should i do

what should i do
02-06-2011, 07:22 AM
Replies: 41
Views: 12,020
Posted By sstumpf

well i got it taken apart without bending the...

well i got it taken apart without bending the shaft. and everything is fine in there nothing is broke and is all pretty clean. what could it be now
02-06-2011, 06:58 AM
Replies: 41
Views: 12,020
Posted By sstumpf

ok well i might have to go the tacon route. but i...

ok well i might have to go the tacon route. but i must have worded it wrong it will always spin when i do it by hand even when i cant get it to with the transmitter what could it be in that case...
02-05-2011, 06:07 PM
Replies: 41
Views: 12,020
Posted By sstumpf

anybody i dont think i can open this. what can i...

anybody i dont think i can open this. what can i do i dont have a different motor i can try do i just have to buy a new motor
02-05-2011, 05:41 PM
Replies: 41
Views: 12,020
Posted By sstumpf

here is the motor it is a experience touring

here is the motor it is a experience touring
02-05-2011, 05:12 PM
Replies: 41
Views: 12,020
Posted By sstumpf

anybody some help

anybody some help
02-05-2011, 04:50 PM
Replies: 41
Views: 12,020
Posted By sstumpf

i just noticed something when it is not spinning...

i just noticed something when it is not spinning and then it goes to spinning again there is a click in the motor to switch over to start spinning what could this be. also what does the timing do...
02-05-2011, 04:46 PM
Replies: 41
Views: 12,020
Posted By sstumpf

no it doesnt it is the older version of it...

no it doesnt it is the older version of it without screws.
02-05-2011, 10:09 AM
Replies: 41
Views: 12,020
Posted By sstumpf

ya i dont see any screws i think it is probaly...

ya i dont see any screws i think it is probaly something in there but there are no screws to take off where would the be i am going to sit down and work on it tonite when i get home and try to find...
02-05-2011, 05:53 AM
Replies: 41
Views: 12,020
Posted By sstumpf

i took the motor out and the pinion gear off to...

i took the motor out and the pinion gear off to see what it does and it will turn for a while then it will stop like it is stuck and cant turn anymore then if you what for a bit it will turn again...
02-05-2011, 05:47 AM
Replies: 41
Views: 12,020
Posted By sstumpf

this motor doesnt come apart

this motor doesnt come apart
02-05-2011, 05:13 AM
Replies: 41
Views: 12,020
Posted By sstumpf

how do i do that

how do i do that
02-05-2011, 05:05 AM
Replies: 41
Views: 12,020
Posted By sstumpf

i dont know if it is that because when the motor...

i dont know if it is that because when the motor is out not even touching the spur it does the same thing
02-04-2011, 09:22 PM
Replies: 41
Views: 12,020
Posted By sstumpf

im not that familer with the brushless all i know...

im not that familer with the brushless all i know is it sometimes turns and sometimes doesnt and has a high pitch hum. can you take the engine apart to replace a berring
02-04-2011, 09:13 PM
Replies: 41
Views: 12,020
Posted By sstumpf

all wires are fine does any body else have some...

all wires are fine does any body else have some input on my problem
02-04-2011, 09:01 PM
Replies: 41
Views: 12,020
Posted By sstumpf

it is a team orion vortex motor with a ez run esc...

it is a team orion vortex motor with a ez run esc on a stampede with 3s 3000mAh 20c battery
02-04-2011, 08:52 PM
Replies: 41
Views: 12,020
Posted By sstumpf

brushless motor stopped working

it worked fine then it started not to spin and it just makes a high pitch humming noise then it will kick back in and spin for a second then goes back out what is this
Showing results 1 to 22 of 22


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.